MATERIE PLASTICHE - Regolazione Industriale
Transcript of MATERIE PLASTICHE - Regolazione Industriale
POLIETILENE (PE) - POLIPROPILENE (PP) - POLIVINILCLORURO (PVC)
CARATTERISTICHE TECNICHE
I dati qui indicati sono ricavati da misurazioni effettuate in laboratorio con una temperatura di 23°C ed una umidità relativa del 50%. Essi sono comunque indicativi e non comportano impegno o responsabilità da parte nostra.
PROPRIETA’ PROPERTY
UNITA’ UNIT
METODOMETHOD
PE300
PE500
PE1000 PP PVC
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Peso specificoDensity gr/cm3 ISO 1183 0,95 0,95 0,94 0,91 1,42
Tensione di snervamentoTensile stress at yeld Mpa DIN EN ISO
527 22 28 22 32 58
Allungamento a rotturaElongation at break % DIN EN ISO
527 500 300 350 70 15
Allungamento a snervamentoElongation at yield % DIN EN ISO
527 9 8 10 8 3
Modulo di elasticitàModulus of elasticity Mpa DIN EN ISO
527 800 850 800 1400 3000
Durezza ShoreShore hardness - ISO 868 62 66 64 70 62
Resistenza all’urtoImpact strength KJ/m2 DIN EN ISO
179 NR NR NR NR NR
ResilienzaResilience KJ/m2 DIN EN ISO
179 13 50 NR 7 4
Coefficiente di attrito dinamicoDynamic friction coefficient - ISO/DTR 7147 0,12 0,12 0,10
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Punto di fusioneMelting point °C - 130/135 130/135 130/135 164 86/90
Temperatura di esercizioService temperature °C - -50/+80 -100/+80 -260/+80 0/+100 0/+60
Coefficiente di dilatazione lineareThermal coefficient of linear expansion K-1 DIN 53752 1,8x10-4 1,8x10-4 1,6x10-4 1,6x10-4 0,8x10-4
Conducibilità termicaThermal conductivity W/m•K DIN 52612 0,38 0,38 0,38 0,22 0,159
Comportamento alla combustioneBurning behaviour - UL 94 HB HB HB HB VO
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Rigidità dielettricaDielectric strength KV/mm IEC 243-1 50 44 44 52 39
Resistenza superficialeSurface resistivity 0hm DIN IEC 167 1014 1014 1014 1014 1013
MA
TERIE P
LASTIC
HE / PLA
STIC M
ATERIA
LS
MATERIE PLASTICHEPLASTIC MATERIALS
MATERIE PLASTICHE CONDUTTIVE CONDUCTIVE PLASTIC MATERIALS
MATERIE PLASTICHE ANTISTATICHEANTISTATIC PLASTIC MATERIALS
POLICARBONATO E ACRILICO (PMMA)
TABELLA COMPATIBILITà CHIMICACHEMICAL COMPATIbILITY CHART
1
7
10
12
16
1
PROPRIETA’ PROPERTY
UNITA’ UNIT
METODOMETHOD
CONDIZIONICONDITION PA6 PA6 +
MoS2PA6
reinforced
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Carico di rottura / Tensile strength at breakMPa ISO 527 dry 80 75 93
MPa ISO 527 moist 50
Allungamento di rottura / Elongation at break% ISO 527 dry 50-100 25 5
% ISO 527 moist 200
Modulo elastico di trazione / Modulus of elasticity in tensionMPa ISO 527 dry 3000 2700 4200
MPa ISO 527 moist 1500
Charpy impact strength+ 23°C kJ/m² ISO 179/1eU dry no break no break
- 40°C kJ/m² ISO 179/1eU dry no break
Charpy impact strength (notched)kJ/m² ISO 179/1eA dry 70
kJ/m² moist
Durezza / Hardness Shore, scale D ISO 868 dry 82 80 80
Tempo limite di snervamento Time yield limit σ 1/1000
23°C/50% RH MPa ISO 899 moist 5,5
100°C MPa ISO 899 dry 2,5
Apparent modulus E C/1000 2O 23°C/50% RH MPa ISO 899 moist 230
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Temperatura di distorsione Heat distortion temperature
Method A °C ISO 75 dry 55-75 168
Method B °C ISO 75 dry >160
Punto di fusione / Melting point Method A °C ISO 3146 220 220 215
Massima temperatura di funzionamento (poche ore) Max. service temperature for few hours operation °C ≤ 180
TEP 5 000 hours (50% of tensile strength) 1) °C IEC 216 90
TEP 20 000 hours (50% of tensile strength) 1) °C IEC 216 75 140
Coefficiente di dilatazione termica lineare Thermal coefficient of linear expansion 1/K.10-5 DIN 53752 dry 7-10
Cond. termica / Thermal cond. Method A W/(K.m) dry 0,23
Calore specifico / Specific heat J/(g.K) IEC 1006 dry 1,7
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Costante dielettrica Dielectric constant
1 MHz IEC 250 dry 3,5
IEC 250 moist 7,0
Fattore di dissipazione Dissipation factor tan δ
1 MHz IEC 250 dry 0,023
IEC 250 moist 0,3
Rigidità dielettrica / Dielectric strengthKV/mm IEC 243 dry 100
KV/mm IEC 243 moist 60
Resistività / Volume resistivityΩ.cm IEC 93 dry 1015 >1012 >1012
Ω.cm IEC 93 moist 1012
Resistività superficiale / Surface resistivity ROAΩ IEC 93 dry 1013 >1012 >1011
Ω IEC 93 moist 1010
Resistance to trackingResistenza alla corrente di fuga
KA/ KB method IEC 112 dry/moist KB > 600
KC method IEC 112 dry/moist KC > 600
PROPRIETA’ VARIE / MISCELLANEOUS PROPERTIES
Densità / Mass density Method D, E g/cm³ ISO 1183 1,13 - 1,15 1,15 1,15
Assorbimento di umidità Moisture absorption at 23°C, 50% RH Saturation % ISO 62 3,0± 0,4 3
Assorbimento acqua Water absorption at 23 °C Saturation % ISO 62 8,0± 0,5 8
Comport. al fuoco / Fire performance Flameability Acc. VDE VDE 0304 II b
Flameab. of interior mat. in passanger cars h>1mm mm/min FMVSS 302 < 100
Flameability according UL Stand. UL 94 HB HB HB
Resistenza all’usura / Resistance to wear μm/km ISO 7148-2
PA 6.6 PA 6.6HI PA 6.6+PE
PA 6.6+30%
GlassfibrePOM-C POM-
C+PEPOM-C +
PTFE
POM-Cmetal
detectablePOM-H PET-C
80 50 65 100 70 40 63 56 72 80
60
50 32 11 8 40 7 22 10 40 20
150
3200 2000 2700 4800 3000 2200 2800 3200 3100 3200
1600
no break no break 35 20 no break 17 90 no break 82
no break no break 80
80 80 3 2,5 11 14
18
80 80 85 81 77 80 81 84 81
6,0 14 12
3,5 60
400
100 64 120 250 110 120 98 105 67
>200 132 250 160 165
255 263 255 164-168 165 178 255
≤200 200 140 100 160
95 115
80 150 100 100 100
7-10 8,5 2-3 11 14 120 10 6
0,23 0,27
1,7 1,5 1,5 10
3,2 3,3 3,8 4,4 3,7 3,3
5
0,026 0,024 0,003 0,02
0,2
120 31 30 >20 33 50
80
1015 1015 >1012 1015 1014 >1013 >1012 1016
1012
1013 >1012 1013 1011 1014 >1013 >1012 >1012
1010
KB>600 KB>600 KA>450
KC>600 KC>600
1,15 1,08 1,12 1,35 1,41-1,43 1,34 1,44 1,56 1,42-1,43 1,36
2,8± 0,3 2,2 1,5 0,20 0,2 0,2 <0,1 0,2 ~0,23
8,5± 0,5 2,2 8,5 5,5 0,25 0,8 0,6 0,5
II b BH 3-25 mm/min 11 b
<100 <100
HB HB HB HB HB HB HB HB HB
4,3 2,1 3 22
MA
TERIE P
LASTIC
HE / PLA
STIC M
ATERIA
LSMA
TER
IE P
LAST
ICH
E /
PLA
STIC
MAT
ERIA
LS
32
PROPRIETA’ PROPERTY
UNITA’ UNIT
METODOMETHOD
CONDIZIONICONDITION
PET-High imp.
PET-C+solidlubricant PBT
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Carico di rottura / Tensile strength at breakMPa ISO 527 dry 85 75 56
MPa ISO 527 moist
Allungamento di rottura / Elongation at break% ISO 527 dry 23 5 >50
% ISO 527 moist
Modulo elastico di trazione / Modulus of elasticity in tensionMPa ISO 527 dry 3250 3230 2600
MPa ISO 527 moist
Charpy impact strength+ 23°C kJ/m² ISO 179/1eU dry 59 23 no break
- 40°C kJ/m² ISO 179/1eU dry
Charpy impact strength (notched)kJ/m² ISO 179/1eA dry 3,9 10 6
kJ/m² moist
Durezza / Hardness Shore, scale D ISO 868 dry 84 81 80
Tempo limite di snervamento Time yield limit σ 1/1000
23°C/50% RH MPa ISO 899 moist
100°C MPa ISO 899 dry
Apparent modulus E C/1000 2O 23°C/50% RH MPa ISO 899 moist
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Temperatura di distorsione Heat distortion temperature
Method A °C ISO 75 dry 93,6 50
Method B °C ISO 75 dry 189,5 135
Punto di fusione / Melting point Method A °C ISO 3146 249 235
Massima temperatura di funzionamento (poche ore) Max. service temperature for few hours operation °C 160 160
TEP 5 000 hours (50% of tensile strength) 1) °C IEC 216 115 115
TEP 20 000 hours (50% of tensile strength) 1) °C IEC 216 100 100 9-15
Coefficiente di dilatazione termica lineare Thermal coefficient of linear expansion 1/K.10-5 DIN 53752 dry 6
Cond. termica / Thermal cond. Method A W/(K.m) dry
Calore specifico / Specific heat J/(g.K) IEC 1006 dry
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Costante dielettrica Dielectric constant
1 MHz IEC 250 dry 3,2
IEC 250 moist
Fattore di dissipazione Dissipation factor tan δ
1 MHz IEC 250 dry
IEC 250 moist
Rigidità dielettrica / Dielectric strengthKV/mm IEC 243 dry
KV/mm IEC 243 moist
Resistività / Volume resistivityΩ.cm IEC 93 dry 5x1013
Ω.cm IEC 93 moist
Resistività superficiale / Surface resistivity ROAΩ IEC 93 dry >1013 >1012
Ω IEC 93 moist
Resistenza alla corrente di fugaResistance to tracking
KA/ KB method IEC 112 dry/moist
KC method IEC 112 dry/moist
PROPRIETA’ VARIE / MISCELLANEOUS PROPERTIES
Densità / Mass density Method D, E g/cm³ ISO 1183 dry 1,4 1,38 1,3
Assorbimento di umidità Moisture absorption at 23°C, 50% RH Saturation % ISO 62 0,3 ~0,23
Assorbimento acqua Water absorption at 23 °C Saturation % ISO 62 0,5 ~0,5 0,5
Comport. al fuoco / Fire performance Flameability Acc. VDE VDE 0304 dry
Flameability of interior materials in passanger cars h>1mm mm/min FMVSS 302 moist
Flameability according UL Stand. UL 94 HB HB HB
Resistenza all’usura / Resistance to wear μm/km ISO 7148-2 dry 1,9 1,1
PEEK PEEK+30%GLASSFIBRE
PEEK+30%CARBON FIBRE
PEEKCERAMIC FILLED PEI PEI+30%
GLASSFIBRE PPS PPS+40%GLASSFIBRE PPSU
97 155 240 95 105 169 33 185 70
25 2 1,7 20 60 1,9 >60
3600 11000 25 4100 3200 9300 4200 14000 2300
no break 11,3 45 no break no break no break 45 no break
section break
8,9 6,4 7 break
7 break
88 91 86 93 84
152 315 336 155 190 210 95 200 207
210 200 212 115 270
340 340 343 ca. 340 280 280 225
300 240
260
4,7 1,7 5 0,45 5 5,5 3 5,6
0,25 0,92
8
3,2 3.4
0,004 0,004 0,0023
20 20
1016 1016 >1013 >1013 >1012 >1012 >1013
>1013 >1015 >1012 >1012 >1015
1,32 1,51 1,4 1,49 1,27 1,51 1,35 1,64 1,29
0,1 0,11 0,7 0,37
0,5 0,04 0,04 0,4 1,25 0,02 0,02 1,1
V0 V0 V0 V0 V0 V0 V0 V0 V0
MA
TERIE P
LASTIC
HE / PLA
STIC M
ATERIA
LSMA
TER
IE P
LAST
ICH
E /
PLA
STIC
MAT
ERIA
LS
54
POLITETR AFLUOROETILENE (PTFE)
CARATTERISTICHE TECNICHE
Dati rilevati ad una temperatura di +23°C
PROPRIETA’ PROPERTY
VALORE VALUE
UNITA’ UNIT
METODOMETHOD
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Peso specifico / Density 2,18 gr/cm3 ASTM D 792
Carico di rottura / Tensile strength at break 30 N/mm2 ASTM D 1457
Allungamento a rottura / Elongation at break 300 % ASTM D 1457
Resistenza compressione 1% di deformazioneCompression strength deformation 1% 4,5 N/mm2 ASTM D 695
Deformazione sotto carico 14 N/mm2 - 24 hCompression strength 14 N/mm2 - 24 h 14,5 % ASTM D 621
Durezza / Shore hardness 55 - ASTM D 2240
Coefficiente di attrito / Friction coefficient 0,05 - (1)
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Coefficiente dilatazione lineare
Coefficient of linear expansion16 °C-1•10-5 ASTM D 896
Conducibilità termica / Thermal conductivity 0,23 W/m•K Cencho - Fitch
Temperatura di esercizio / Service temperature -200 +260 °C -
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Costante dielettrica / Dielectric constant 2,1 - ASTM D 150
Fattore di dissipazione / Dissipation factor <0,0002 - ASTM D 150
Resistività di volume / Specific volume resistance 1017 Ohm/cm ASTM D 257
Resistività di superficie / Specific surface resistance 1015 Ohm ASTM D 257
PTFE SUPERCONDUTTIVO
CARATTERISTICHE TECNICHE
Dati rilevati ad una temperatura di +23°C
PROPRIETA’ PROPERTY
VALORE VALUE
UNITA’ UNIT
METODOMETHOD
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Densità / Density 2,12 - 2,18 g/cm3 ASTM D 792
Durezza / Shore hardness >51 - ASTM D 2240
Resistenza a trazione / Tensile strength >24 N/mm2 ISO12086ISO 527
Allungamento a rottura / Breaking elongation >210 % ISO12086ISO 527
Coefficiente di attrito dinamicoDynamic friction coefficient 0,06 ASTM D 1894
ASTM D 3702 -
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Resistività di volume / Volume resistance 104 Ohm x cm ASTM D 257
Resistività di superficie / Surface resistance 104 Ohm ASTM D 257
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Temp. di esercizio (min - max)
Service temp. (min-max)- 200 /+ 200 -
Coeff. dilat. termica lineareLinear thermal coeff. of expansion 12-13 105(mm/mm)/°C Simile alla
ASTM D 696
MA
TERIE P
LASTIC
HE CO
ND
UT
TIVE / CO
ND
UC
TIVE PLA
STIC M
ATERIA
LSM
ATE
RIE
PLA
STIC
HE
/ PL
AST
IC M
ATER
IALS
76
POM-C CONDUT TIVO
INFORMAZIONI SUL PRODOTTO / PRODUCT INFORMATION
Nome commerciale / Trade name POM-C CONDUTTIVO
Abbreviazione ISO 1043 / Abbreviation ISO 1043 POM LF
Designazione / Designation Polyoxymethylene conductive
Tipo di polimero / Type of polymer Thermoplastic
Conformità alimentare / Food compliance bfR No
Conformità alimentare / Food compliance FDA No
Colore / Colour Black
PROPRIETA’ / PROPERTIES
Densità / Density 1.45 g/cm3 ISO 1183
Modulo di elasticità / Tensile modulus of elasticity 2,800 MPa ISO 527-2
Resistenza superficiale / Specific surface resistance 102 Ohm IEC 60093
Temperatura massima / Temperature for usage in air 140° C
Tolleranza lunghezza / Tolerance length 0% to 3%
Tolleranza larghezza / Tolerance width 1% to 4%
MA
TER
IE P
LAST
ICH
E CO
ND
UT
TIV
E /
CON
DU
CTI
VE
PLA
STIC
MAT
ERIA
LSPROPRIETA’ PROPERTY
VALORE VALUE
UNITA’ UNIT
METODOMETHOD
PROPRIETA’ FISICHE / PHYSICAL PROPERTIES
Densità / Density 1.45 g/cm3 ISO 1183
Assorbimento di umidità / Moisture pick-up till saturation 0.20 % ISO 62
Assorbimento di acqua / Water absorption till saturation 0.70 % ISO 62
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Carico di snervamento / Tensile stress at yeld 63 Mpa ISO 527-2
Carico di rottura / Tensile stress at break - Mpa ISO 527-2
Allungamento a rottura / Elongation at break 17 % ISO 527-2
Coefficiente di elasticità / Tensile modulus of elasticity 2800 Mpa ISO 527-2
Elasticità modulare / Flexural modulus of elasticity 2700 Mpa ISO 178
Durezza Rockwell / Rockwell hardness M 97 ISO 2039-2
Resistenza all’urto (met. Charpy) / Charpy impact strength 120 kJ/m2 ISO 179/1eU
Resistenza all’urto (met. Charpy) Charpy impact strength - notched 5.5 kJ/m2 ISO 179/1eA
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Resistenza di isolamento / Specific insulation resistance 103 Ohm.m IEC 60093
Resistività superficiale / Specific surface resistance 102 Ohm IEC 60093
Costante dielettrica / Dielectric constant (at 1 MHz) - 106 Hz IEC 60250
Costante dielettrica / Dielectric constant (at 100 Hz) - 102 Hz IEC 60250
Fattore di dissipazione / Dissipation factor (at 1 MHz) - 106 Hz IEC 60250
Fattore di dissipazione / Dissipation factor (at 100 Hz) - 102 Hz IEC 60250
Rigidità dielettrica / Dielectric strength K20/K20 - kV/mm IEC 60243-1
Indice di comparazione (CTI) / Comparative tracking index (CTI) - IEC 60112
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Temp. di utilizzo di picco / Temp. for usage in air (max short term) 140 °C
Temp. di utilizzo in continuo / Temp. for usage in air (max lasting) 100 °C
Temp. min. di utilizzo / Minimum service temp. in air -20 °C
Temperatura di distorsione / Heat distortion temperature 100 °C ISO 75-2
Coefficiente di dilatazione lineare / Coefficient of linear expansion 1.1 10-4K ISO 11359
Conduttività termica / Thermal conductivity 0.30 W/(K m) DIN 52612
Infiammabilità secondo UL / Flammability according UL Standard HB Class UL 94
Temp. di rammollimento (met. Vicat) / Vicat softening temp. 150 °C ISO 306
Punto di fusione / Melting point 166 °C ISO 3146
MA
TERIE P
LASTIC
HE CO
ND
UT
TIVE / CO
ND
UC
TIVE PLA
STIC M
ATERIA
LS
98
PE 1000 NERO ANTISTATICO
INFORMAZIONI SUL PRODOTTO / PRODUCT INFORMATION
Colore / Colour black - -
Densità / Density > 0,93 g/cm3 ISO 1183
Assorb. acqua / Water absor. - 23°C/50% <0,01 % ISO 62
Assorb. acqua / Water absor. - in water < 0,01 %
POM-C ANTISTATICO
INFORMAZIONI SUL PRODOTTO / PRODUCT INFORMATION
Densità / Density
1,35 g/cm3 ISO 1183
PROPRIETA’ PROPERTY
VALORE VALUE
UNITA’ UNIT
METODOMETHOD
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Carico di rottura / Tensile stress at break >15/- MPa ISO 527
Allungamento di rottura / Elongation at break >150 % ISO 527
Coefficiente di elasticità / Coefficient of elasticity (pulling test) 950 MPa ISO 527
Prova di compress. / Press. test (compress. strength at 1/2/5% nominal) 6/10,5/18 MPa ISO 604
Resistenza all’urto (met. Charpy) / Charpy impact strength k.B. kJ/m2 ISO 179
Resistenza all’urto (met. Charpy) / Charpy impact strength (Notched) >80 kJ/m2 ISO 179
Durezza / Shore hardness 61-63 - DIN 53505
Coefficiente d’attrito / Coefficient of sliding friction (dry) 0,1-0,2 - -
Resistenza all’abrasione / Sand Slurry test 130 % ISO 15527
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Rigidità elettrica / Electric strength - kV/mm IEC 60243
Resistività / Specific contact resistance <106 Ohm x cm IEC 60093
Resistività superficiale / Surface resistance >109 Ohm IEC 60093
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Punto di fusione / Melting temperature 130-135 °C ISO 3146
Conduttività termica / Heat conductivity - 23°C 0,4 W/(K x m) ISO 52612
Coefficiente di dilatazione termica lineare:Linear thermal coefficient of expansion: ISO 11359
Valore medio tra: / Average value between: 23 and 60°C 20x10-5 m/(m x K)
Massima temp. di utilizzo / Upper service temperature in air:
Di picco - Short-term service temperature 90 °C -
Continua: massimo 5000 ore / Constant: for 5000h 80 °C -
Temperatura minima di utilizzo / Lower service temperature -150 °C -
Comportamento alla combustione UL 94 / Burning behaviour UL 94 HB - -
MA
TER
IE P
LAST
ICH
E A
NTI
STA
TIC
HE
/ A
NTI
STA
TIC
PLA
STIC
MAT
ERIA
LSM
ATER
IE PLA
STICH
E AN
TISTATIC
HE / A
NTISTA
TIC PLA
STIC M
ATERIA
LS
PROPRIETA’ PROPERTY
VALORE VALUE
UNITA’ UNIT
METODOMETHOD
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Carico di rottura / Tensile strength at break 40 MPa ISO 527
Allungamento di rottura / Elongation at break 72 % ISO 527
Modulo elastico di trazione / Modulus of elasticity in tension 1380 MPa ISO 527
Charpy impact strength no break kJ/m² ISO 179/1eU
Durezza / Hardness Shore, scale D 74 ISO 868
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Rigidità dielettrica / Dielectric strength 14 KV/mm IEC 243
Resistività / Volume resistivity 109-1010 Ω.cm IEC 93
Resistività superficiale / Surface resistivity ROA 109-1010 Ω IEC 93
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Punto di fusione / Melting point Method A 165 °C ISO 3146
1110
POLI
CA
RBO
NAT
O E
ACR
ILIC
O (P
MM
A)
POLICARBONATOPROPRIETA’ PROPERTY
VALORE VALUE
UNITA’ UNIT
METODOMETHOD
PROPRIETA’ FISICHE / PHYSICAL PROPERTIES
Peso specifico / Density 1,2 g/cm3 ISO 1183
Assorbimento di acqua / Water absorption till saturation (24h) 8 mg ISO 62
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Resistenza alla flessione / Flexural strength MPa ISO 178
Resistenza alla trazione / Tensile strength 60 MPa ISO 527
Allungamento a rottura / Elongation at break 80 % ISO 527
Coefficiente di elasticità / Tensile modulus of elasticity 2200 Mpa ISO 527
Modulo di elasticità tangenziale / Shear modulus 700 Mpa ISO 6721-2
Resilienza / Resilience senza rottura kJ/m2 ISO 179
Resilienza con intaglio / Resilience with notch >40 kJ/m2 ISO 179
Durezza al penetratore a sfera / Ball indentation hardness 110 Mpa ISO 2039-1
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Temp. di rammollimento (met. Vicat) / Vicat softening temp. 145 °C ISO 306
Temp. della stabilità dimensionale / Coefficient of linear expansion 135 °C ISO R 75
Temp. d’impiego permanente / Service temperature 115 °C DIN 53446
Coefficiente dilatazione termica / Thermal coefficient of expansion 65x10-6 K-1 DIN 53328
Conduttività termica / Thermal conductivity 0,2 W/Km DIN 52612
Calore specifico / Specific heat 1,17 J/gK -
Ritiro lineare / Linear shrinkage 0,5-0,7 % -
PROPRIETA’ OTTICHE / OPTICAL PROPERTIES
Indice di rifrazione / Refractive index 1,585 nD 20
Trasmissione luminosa / Light transmission 86 %
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Resistività superficiale / Specific surface resistance 1015 Ω DIN 53482
Resistività specifica di massa / Specific mass resistance 1015 Ωcm DIN 53482
Rigidità dielettrica / Dielectric strength >30 kV/mm DIN 53481
Fattore di perdita dielettrico / Dielectric loss factor 50 HZ 1 MHz
8x 10-4
11x 10-4 - DIN 53483
Costante dielettrica / Dielectric constant 50 HZ 1 MHz
3,02,9 - DIN 53483
Resistenza alla corrente di fuga / Resistance to leakage current >200 Kc DIN 53480
COMPORTAMENTO AL FUOCO / REACTION TO FIRE 1B 2 Classe DIN 4102
Lastre in Policarbonato compatto standard, incoloriDIMENSIONI DIMENSIONS
mm
SPESSORITHICKNESS
mm1 1,5 2 3 4 5 6 8 10 12 15
Peso Kg/m2 1,2 1,8 2,4 3,6 4,8 6,0 7,2 9,6 12,0 14,4 18,0
2050x1250 <====> # # # # # # # # # # #
3050x2050 <====> # # # # # # # # #
4050x2050 <====> # # # * *
5050x2050 <====> # # # * *
6100x2050 <====> * * * * *
tagli a misura ed altre dimensioni su richiesta
# da magazzino* su richiesta e quantitativi minimi
UVP - Lastre in Policarbonato compatto protette UV, incoloriLa protezione ai raggi UV s’intende mediante coestrusione sui due lati
DIMENSIONI DIMENSIONS
mm
SPESSORITHICKNESS
mm2 3 4 5 6 8 10 12
3050x2050 <====> # # # # # # # #
4050x2050 <====> * * * *
5050x2050 <====> * * * *
6100x2050 <====> # # # # *
tagli a misura ed altre dimensioni su richiesta
Lastre standard e protette UV - opaline, fumè e goffrateTrasmissione luminosa e densità colore dipendono dallo spessore delle lastre
CODICE opale opale UVP fumè bronzo fumè bronzo UVP goffrato incolore
DIMENSIONI DIMENSIONS
mm
SPESSORITHICKNESS
mm
Trasmissione luminosa spessore 3 mm (valori indicativi)
37/28% 50/28% 51/28% 51/28%
2050x12503050x2050
2 ##
# # # #
3050x20504050x20505050x20506100x2050
3 ####
# #**#
####
#
3050x20506100x2050
4 ##
# ##
##
#
3050x2050 5 # # # #
3050x2050 6 # # #
3050x2050 8 * *
tagli a misura ed altre dimensioni su richiesta
Tolleranze spessori / RitiriSpessori 1,5 mm 2,0 mm 3,0 mm 4 - 15 mm
Tolleranze +/- 10% +/- 10% +/- 5%
Ritiri max 6% 6% 3% 3%
Tubi estrusi in PolicarbonatoL = a richiesta
A mm B mm A mm B mm A mm B mm A mm B mm
8 4-5 32 24-26-27-28 70 62-64-66-67 140 132-134-135-136
9 4-5-6 33 27-28-29-30 72 64-66-68-69 145 138-139-140-14
10 4-5-6-7 35 28-2-30-31 76 68-70-72-73 150 142-144-145-146
12 6-7-8-9 36 29-30-31-32 80 72-74-75-76-77 157 150-151-152-153
13 7-8-9-10 38 30-32-34-35 87 79-81-83-84 160 152-154-155-156
14 8-9-10-11 40 32-34-36-37 90 82-84-85-86 166 159-160-161-162
15 9-10-11-12 42 34-36-38-39 93 86-87-88-89 170 163-164-165-166
16 11-12-13 45 38-39-40-41 100 92-94-95-96 180 172-174-175-176
17 12-13-14 47 39-41-43-44 110 102-104-105-106 200 192-194-195-196
20 14-15-16-17 50 42-44-45-46-47 116 108-110-111-112 208 200-202-203
22 16-17-18-19 52 44-46-48-49 120 112-114-115-116 212 204-206-207
24 18-19-20-21 55 47-49-51-52 125 117-119-120-121 225 217-219-220
25 18-19-20-21-22 60 52-54-56-57 126 119-120-121-122 230 222-224-225
27 20-21-22-23-24 64 56-58-60-61 130 122-124-125-126 240 232-234-235
28 21-22-23-24-25 6 57-58-61-62 133 126-127-128-129 250 244-245
30 22-24-25-26 68 58-60-62-64 134 126-128-129-130
POLIC
ARB
ON
ATO E A
CRILICO (PM
MA
)
# da magazzino* su richiesta e quantitativi minimi
1312
ACRILICO
PROPRIETA’ PROPERTY
VALORE VALUE UNITA’
UNITMETODOMETHOD
GS XT
PROPRIETA’ FISICHE / PHYSICAL PROPERTIES
Peso specifico / Density 1,19 1,19 g/cm3 ISO R 1183 DIN 53479
Indice di viscosità / Viscosity index > 400 ml/g
Assorbimento di acqua / Water absorption till saturation (24h) 0,20 0,30 % ISO R 62 DIN 53495
Assorbimento di acqua / Water absorption till saturation (8 day)) 0,50 0,50 % ISO R 62 DIN 53495
PROPRIETA’ MECCANICHE / MECHANICAL PROPERTIES
Resistenza alla flessione / Flexural strength 125 120 MPa ISO 178 DIN 53452
Modulo elastico a flessione / Flexural modulus 3000 2900 MPa ISO 178 DIN 53452
Resistenza alla trazione / Tensile strength 84 70 MPa ISO R 527 DIN 53455
Allungamento a rottura / Elongation at break 7,5 4 % ISO R 527 DIN 53455
Modulo elastico a trazione / Tensile modulus 3300 3200 MPa ISO R 527 DIN 53455
Resistenza all’urto Cahrpy / Charpy impact strength 12 11 kJ/m2 ISO 179/1D DIN 53453
Resilienza con intaglio / Resilience with notch (+20°C) 2 2 kJ/m2 ISO 179 DIN 53453
Durezza al penetratore a sfera / Ball indentation hardness 190 190 Mpa ISO 2039-1 ASTM D 785
Resistenza a compressione / Compression strength 130 110 Mpa ISO R 684 DIN 53454
PROPRIETA’ TERMICHE / THERMAL PROPERTIES
Temp. di rammollimento (met. Vicat) / Vicat softening temp. >110 >100 °C ISO 306 DIN 53460
Temp. della stabilità dimensionale / Coefficient of linear expansion 100 90 °C ISO R 75/A DIN 53461
Temp. d’impiego permanente / Service temperature 80 70 °C DIN 53446
Coefficiente dilatazione termica / Thermal coefficient of expansion 70x10-6 70x10-6 K-1 DIN 53328
Coefficiente di isolamento termico 3 mmThermal insulation coefficient 10 mm
5,34,5
5,34,5
W/m2°CW/m2°C DIN 4701
Conduttività termica / Thermal conductivity 0,19 0,19 W/Km DIN 52612
Calore specifico / Specific heat 1,47 1,47 J/gK ASTM C 351
Ritiro lineare / Linear shrinkage 0,4-1,1 0,5-1,3 %
Ritiro lineare massimo dopo riscaldamento <3 mmMaximum linear shrinkage after heating >3 mm
22
63
%%
Temp. di inizio degradazione / Degradation temp. 285 240 °C
PROPRIETA’ OTTICHE / OPTICAL PROPERTIES
Indice di rifrazione / Refractive index 1,492 1,492 nD 20 ISO 489 DIN 53491
Trasmissione luminosa / Light transmission 93,5 92 % DIN 5036-T3
PROPRIETA’ DIELETTRICHE / DIELECTRIC PROPERTIES
Resistività superficiale / Specific surface resistance 1014 1014 Ω DIN 53482
Resistività specifica di massa / Specific mass resistance 1015 1015 Ωcm DIN 53482
Rigidità dielettrica / Dielectric strength 30 30 kV/mm DIN 53481
Fattore di perdita dielettrico 50 HZDielectric loss factor 1 MHz
0,060,02
0,0600,025 - DIN 53483
Costante dielettrica 50 HZDielectric constant 1 MHz
3,62,7
3,72,8 - DIN 53483
Resistenza alla corrente di fuga / Resistance to leakage current >600 >600 Kc DIN 43480
COMPORTAMENTO AL FUOCO / REACTION TO FIRE
Temp. di autoaccensione / Ignition temperature ca. 430 ca. 430 °C
Comportamento al fuoco / Reaction to fireB 2M 4
classe 3
B 2M 4
classe 4
GermaniaFrancia
DIN 4102P 92505
BS 476 Part 7
NB: I valori indicati si riferiscono a lastre trasparenti - incolori, rappresentano la media delle prove di laboratorio, devono intendersi unicamente a carattere indicativo
POLI
CA
RBO
NAT
O E
ACR
ILIC
O (P
MM
A)
Lastre acriliche colate colorate, incolorisecondo ISO 7823-1: 1991 / DIN 16957: 1985 / UNE-EN ISO 7823-1: 1996 / ASTM D702-81Tolleranza spessori secondo ISO 7823-1 / DIN 16957: Spessore s +/- (0,4 mm + 0, 1s)
DIMENSIONI DIMENSIONS
mm
SPESSORITHICKNESS
mm2 2,5 3 4 5 6 8 10 12 15 18 20 25
Peso Kg/m2 2,4 3,0 3,6 4,8 6,0 7,2 9,6 12,0 14,4 18,0 21,6 24,0 30,0
2020x1320 <====> # # # # # # # # # # # #
2650X1850 <====> * * * * * * * * * * * * *
2650X2030 <====> * * * * * * * *
3050X2030 <====> # # # # #
3000X2000 <====> # # # # # # #
tagli a misura ed altre dimensioni su richiesta
Lastre acriliche estruse, incolorisecondo ISO 7823-2 / DIN 16958
DIMENSIONI DIMENSIONS
mm
SPESSORITHICKNESS
mm1,5 2 2,5 3 4 5 6 8 10 12 15 18 20
Peso Kg/m2 1,8 2,4 3,0 3,6 4,8 6,0 7,2 9,6 12,0 14,4 18,0 21,6 24,0
2000x1250 <====> #
3050x2020 <====> * #
3050x2050 <====> # # # # # # # * * * *
4050x2050 <====> # # # #
5050x2050 <====> # # # #
6050x2050 <====> # # # *
tagli a misura ed altre dimensioni su richiesta
Tolleranze spessori / RitiriSpessori / Thickness 1,5 mm 2,0 - 2,5 mm 3,0 - 10,0 mm
Tolleranze -0,1 / + 0,2 mm +/- 10% +/- 5%
Ritiri longitudinali max 6% 6% 3%
Ritiri trasversali max 0,5% - 1,0 %
# da magazzino* su richiesta e quantitativi minimi
POLIC
ARB
ON
ATO E A
CRILICO (PM
MA
)
Tubi estrusi in Polimetilmetacrilato (PMMA)L = 2000 mm L = 2050 mm
A mm B mm A mm B mm A mm B mm A mm B mm
7 5 24 18-20 40 30-32-34-36 125 115-117-119
8 4 25 19-21 44 34-36-38 130 120-122-124
10 6-7-8 26 20-22 45 39 134 124-126-128
12 6-8-10 28 22-24 50 40-42-44-46 150 140-142-144
13 9-10 30 20-22-24-26 56 48-50 160 150-152-154
14 8-10 32 24-26 60 50-52-54-56 170 172-174
15 9-10-11 34 28 64 54-56-58-60 180 170-172-174
16 12 36 28-30 70 60-62-64-66 185 185-187-189
18 12-14 38 32 76 66-68-70 200 190-192-194
20 14-16 40 30-32-34-36 80 70-72-74-76 220 220-222-224
22 16-18 90 80-82-84-86 240 230-232-234
100 90-92-94-96 250 240-242-244
110 100-102-104 300 290-292
120 110-112-114 1514
%
PA 6PA6+MoS2
PA 6.6PA 6.6+30%
GlassfibrePA6.6+PE
PA 6 C
POM-CPOM-C
POM-C+PEPOM-HPOM-H
PET-CPET-C PET
C+solidlubricant)
PET-HPBT
PEEKPEEK+30%Glassfibremodified
PEIPEI+30%
Glassfibre
PPSPPS+40%Glassfibre
PPSU
Acetone H D D A A
Acetylchloride 10 A A A A
Acetylene A A A A A A
Alkylbenzoic TR A A A A A
Alu. salts of min.acids TR A B B A B
Formic acid TR B/C D D A B D
Ammonia TR A A C
Benzene, Benzaldehyde TR A
Chlorine moist D D D
Boric acid H A A A A
Bromwater H A A A A A
Butadien TR D D D C
n-Butyleneglycol 10 A A A A A
Calcium chloride alcoholic
Chlorine, Chlorine moist 10 A A A
Chlorobenzene 10 A A A A A
Chloroform 10 A D D
Citric acid TR B A A A A
aqueous TR A A A A A A
Cyclohexane/Cyclopetone H A A A A A
Dichlortrehylene TR B/C B/C B/C A/B A
Dichlortetrafluorethan TR A A A A A A
Dimethyleter TR A/B
Inert Gas 10 D A A A A A
Developing liquid 85
Mineral oil, Natural gas TR A A A A A
Acetic acid aqueous TR A A A A A
Ethanol GL D A A
Essential oils >50 D C C B A
Alcoholic fat >20 D B B A B A B
Fatty acid TR A A A A
Flurinated hydrocarbons TR A A
Flurinated hydroacid aq. TR B A A
Fixer solution GL B A A A
Galvanic baths >80 D D D A
Glycerine 10 A A A A A A
Glyceral TR A A A A A A A
Glyceral acid aqueous TR A A A A
Glysantin H A A A A A A
Uric acid aqueous TR A A A
Helium and rare gas H A A A A A A
Heptan Hexan TR A/B D D A B
Hydraulic oils TR D D D A
Impregnating oils A A A A A
Iso-octan TR A A A A
Isocyante >100 B/D D D A A A
Cold machine oil TR A A A A A A A
Potash lye A A A
Potasiumchloride 10 A A
Hydrofluoristic acid 50 B
Carbon dioxide TR A B B A B A B
Super Otto-fuel TR/100 A D D A
Diesel fuel 10 B A A A A A
Turbine aircraft fuel 37,5 D
Kerosene A A A A
TAB
ELLA
CO
MPA
TIB
ILIT
A’ C
HIM
ICH
E /
CH
EMIC
AL
COM
PATI
bIL
ITY
CH
AR
T %
PA 6PA6+MoS2
PA 6.6PA 6.6+30%
GlassfibrePA6.6+PE
PA 6 C
POM-CPOM-C
POM-C+PEPOM-HPOM-H
PET-CPET-C PET
C+solidlubricant)
PET-HPBT
PEEK
PEEK+30%Glassfibre
modified
PEI
PEI+30%Glassfibre
PPS
PPS+40%Glassfibre
PPSU
Soldering solution H D D A A
Magnesium salt aqueous 10 A A A A
Seawater A A A A A A
Methan TR A A A A A
Methyl acetate TR A B B A B
Methylene Chloride TR B/C D D A B D
Methylene Glycol TR A A C
Methylenglycolacetate TR A
Mixed acids D D D
Engine oil H A A A A
Naphtalene H A A A A A
Naphtalenesulfanacids TR D D D C
Sodium salts aqueous 10 A A A A A
Sodium hypophosphit
aqueous 10 A A A
Sodium bisulfit aqueous 10 A A A A A
Caustic soda solution 10 A D D
Nitrobenzene TR B A A A A
Octane Octene TR A A A A A A
Oleric acid H A A A A A
Ozone TR B/C B/C B/C A/B A
Petroleum TR A A A A A A
Phenylethylalcohol TR A/B
Phosphoric acid 10 D A A A A A
85
Propane TR A A A A A
Mercury TR A A A A A
Mercury chlorid aqueous GL D A A
Nitric acid >50 D C C B A
Hydrochloric aqueous >20 D B B A B A B
Oxygen under pressure TR A A A A
Sulphurdioxid dry TR A A
moist TR B A A
Sulphereous acid GL B A A A
Sulphuric acid >80 D D D A
Sodium Carbonate 10 A A A A A A
Nitrogen gas TR A A A A A A A
Styrol TR A A A A
Turpentine oil H A A A A A A
Tetrachloride-carbon TR A A A
Transformer oil H A A A A A A
Trichlorethylene TR A/B D D A B
Uraniumfloride TR D D D A
Urine A A A A A
Vinylchloride TR A A A A
Steam >100 B/D D D A A A
Hydrogen TR A A A A A A A
Hydreogensuperoxid A A A
Acidity of Wine 10 A A
50 B
Xylol TR A B B A B A B
TR/100 A D D A
Zincchloride 10 B A A A A A
37,5 D
Zinc A A A A
TAB
ELLA CO
MPA
TIBILITA
’ CH
IMIC
HE / C
HEM
ICA
L COM
PATIbILITY
CH
AR
T
1716