WICK 06 2 - 1 (704) 849-9209 · (a seconda dei modelli di macchina ... Grazie alla presa di moto...
Transcript of WICK 06 2 - 1 (704) 849-9209 · (a seconda dei modelli di macchina ... Grazie alla presa di moto...
WICKMAN
E’ un apparecchio da posizionarsi sul carro trasversale per creare posteriormente scarichi o sedi di guarnizioni.Gli utensili, con stelo 16x16, devono essere adeguatamente profilati.Il blocchetto portautensile è fulcrato e quindi, quando spinto, è in grado di ruotare legger-mente portando l’utensile a lavorare il pezzo. La piccola lavorazione compiuta e la distan-za tra fulcro e pezzo sono tali che rendono l’arco di cerchio percorso dall’utensile del tuttoapprossimabile ad un movimento rettilineo.Una staffa posizionata sull’esagono centrale oppure su di una spinta assiale indipendente(a seconda dei modelli di macchina) spingerà il blocchetto.
MOLLE A TAZZA
SPINTA
FULCRO
APPARECCHIO BASCULANTE PER SCARICHI POSTERIORI BACK-SIDE TURNING ATTACHMENT FOR SMALL GROOVES
Good to make back-side easy turning operations. The standard tool body is 16mm x 16mm. The tool is not included and must be properly profiled by the customer. The cutter moves around but because of its distance to the pivot and its small movement inside the part, it is impossible to understand it, looking at the final result. The tool-holder is pushed by a bracket fixed on centre block, that it is included
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
Wickman 1”3/4-6
WICKMAN
Grazie alla presa di moto sincrona, la broccia, chiusa nella pinza ER32, è in grado di
eseguire poligoni o profili geometrici all’interno del pezzo.
Naturalmente ciò è possibile grazie ad una leggera inclinzione dell’asse di rotazione nel
mandrino portautensile.
This attachment is designed to create polygons o r geometrical profiles inside the
component. It has to be fitted on the centre block of the machine (longitudinal slide).
The tool rotates at the same speed as the bar.
The standard tool-spindle uses ER type collets.
The tool spindle has a slight inclination versus the axis of the component in order to reduce
the axial load during the broaching operation
APPARECCHI BROCCIATORE SINCRONO BROACHING ATTACHMENT BROCIADOR MehrkantstoBenrichtung
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
We have always supplied the Wickman threading attachment driven by electromagnetic
clutches.
The self-adjusting electromagnetic clutches have oversized power and they are piloted by our
electronic Power Unit.
The microswitches give the Power Unit the right inputs to drive the attachment properly.
They can also check any malfunctioning (tap stuck in the component or missed threading op-
eration), and allow the Unit to stop the machine.
The threading spindle is usually supplied for ER type collets, some spindles are now available
in coolant fed version (high pressure fluid inside bored tap).
All gears and shafts are hardened and grinded.
The mechanical parts are supplied fitted together as much as possible to make fitting easier .
WICKMAN APPARECCHIO FILETTATORE FULL THREADING ATTACHMENT ROSCADOR TARUDEUR Gewindeschneideinrichtung
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
Wickman 1”-6
Wickman 1”3/4-6
WICKMAN
Questo mandrino, ruotando in senso opposto alla barra, fora ad una velocità che è la
somma della sua rotazione e di quella della barra. La velocità di rotazione del mandrino
è rapportata in modo diverso a quella della macchina grazie a alcune coppie di
ingranaggi, fornite con l’apparecchio.
La pinza portapunta è del tipo ER25.
E’ eventualmente disponibile anche la versione con refrigerazione a pressione interna
all’utensile.
The High Speed Drilling Attachment is usually supplied with ER type collets and with
different couples of ratio gears.
It is now available in the coolant fed version: the coolant liquid can be pushed through
the tool at high pressure during the drilling operation.
MANDRINO FORATORE RAPIDO HIGH SPEED DRILLING ATTACHMENT TALADRO RAPIDO Schnellbohreinrichtung
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
WICKMAN CARRO A TORNIRE LONGITUDINAL TURNING CHARIOT Axialschlitten Langdrehschieber
10
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
WICKMAN
Questo dispositivo è concepito per ottenere in modo pratico e veloce delle incisioni sul
pezzo in rotazione.
Le sigle da marcare sul pezzo devono essere incise da ditte professioniste sui dischi
grezzi che forniamo e che trovano alloggiamento sul perno del timbratore.
Il funzionamento è il seguente: il carro trasversale, su cui viene montato il timbratore, si
sposta in avanti sino a che il disco entra in contatto con il pezzo rotante.
Per effetto dell’attrito il disco viene portato in trascinamento ed incide la sigla, fermandosi
poi in una zona scaricata per evitare altri contatti col pezzo.
Durante il ritorno del carrello, un puntalino opportunamente predisposto, provoca la
ricarica dell’apparecchio.
This attachment is used for marking the components in a very simple and quick way,
because it is based on a completely mechanical logic.
The cross slide, with our attachment on, moves forward till the engraved disk touches the
component.
Because of the friction between them, the disk starts to turn and mark the component.
When the engraving is over, the disk stops in a fixed position to avoid further contact whit
the component.
During the return stroke a proper pin fixed on the wall of the machine resets the attach-
ment with the disk able to turn again.
We can supply blank disks only together with the instructions about how to engrave
them.
APPARECCHIO TIMBRATORE MARKING ATTACHMENT Markierer
11
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
The polygon and thread milling attachment can be fitted in any station.
The attachment is usually supplied with 2 couples of gears, the 1:1 thread milling ratio and the
1:2 polygon generating ratio. All the gears and shafts are hardened and grinded.
The tool fitting can be chosen between original Wickman fitting or 8°32’ degree conical shaped +
key.
In case of 8°32’ fitting we can also supply the cutter tool.
As you can see in the picture, they have the possibility to hold 1 cutter
(flats) or 2 cutters at 180° (squares) or 3 cutters at 120° (hexagons).
The cutters can have different widths and they must be grinded by the
user.
We also can supply smaller drill-holders in order to make drilling
operations in the same station where you are fitting the attachment.
Wickman 1”-6
APPARECCHIO POLIGONATORE E FRESAFILETTI POLYGON-GENERATING AND THREAD-MILLING ATTACHMENT POLIGONADOR Y FRESADOR DE ROSCAS APPAREIL A POLYGONER ET FRESAIR LES FILETS Mehrkantdreh Und Gewindefraseinrichtung
WICKMAN
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
WICKMAN
APPARECCHIO POLIGONATORE IN PASSATA POLYGON-GENERATING ATTACHMENT WITH LONGITUDINAL MOVEMENT
Questo apparecchio è dotato di un alberino portautensile sfilabile, che può essere spinto da una staffa montata sul blocco centrale. Una volta che il carro radiale ha raggiunto la posizione di lavoro, si può spingere l’alberino, operando una poligonatura in passata. L’apparecchio trova il suo impiego migliore nella poligonatura di materiali ferrosi, dove, con l’utilizzo di utensili speciali a inserti, si possono risolvere problematiche non superabili con l’apparecchio standard. Inoltre non è trasurabile che il suo impiego possa in alcuni casi evitare il ricorso all’acquisto di dispendiosi carri a croce.
This attachment has got an extractable tool-arbor in the cross slide head. The tool-arbor back end is outside the head, so it can be pushed forward by a bracket fixed on the centre block in the same station. A set of belleville washers will pull the arbor into starting position at the end of the cycle. This kind of attachment is very good for long polygon jobs and even better for hard jobs on steel materials. In this cases we suggest to use special tools with standard inserts. Please note that using this attachment can avoid to buy very expensive compound slides.
alberino sfilabile extractable arbor
molle a tazza belleville washers
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
WICKMAN
This attachment is used to create recesses inside the component. It has to be located on the central block of the machine. After reached the right position inside the component the tool-holder moves upwards, sliding on a 14° degree ramp (that means 1 mm upwards every 4 mm of axial movement of the central block). The length of the recess is usually the same as the length of the cutting tool. However, if you need to create longer recesses, our attachment can also move axially while making the recess.
DATI TECNICI - Rampa inclinata 14° (4mm di corsa assiale corrispondono a 1mm di alzata)- Foro alloggiamento utensile = 25mm di diametro, eccentrico di 1,5MM- Possibilità di avere lubrificazione attraverso un utensile forato- Possibilità di regolare l'altezza della testa portautensile- Possibilità di far compiere all'utensile delle torniture interne in passata (da specificareal momento della richiesta di offerta).•TECHNICAL DATA:- 14° degree ramp- Tool Fitting = 25 mm diameter bore (eccentric)- Possibility of lubrication liquid through the tool- Up and down adjustable toolholder- Possibility of axial movement while recessing
APPARECCHIO RECESSITORE A RAMPA RAMP RECESSING ATTACHMENT CAJEADOR APPAREIL A CHAMBRER Innenausdrehschieber
8
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
APPARECCHIO RECESSITORE A RAMPA TIPO ORIGINALE RAMP RECESSING ATTACHMENT - ORIGINAL GILDEMEISTER DESIGN CAJEADOR APPAREIL A CHAMBRER Innenausdrehschieber
WICKMAN
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105
WICKMAN
L’apparecchio contropoligonatore è dotato di un utensile portalama in grado di ruotare alla
stessa velocità della barra ma con un senso di rotazione opposto.
Questo gli permette di creare degli spacchi a profilo raggiato sull’esterno del pezzo.
This attachment is designed to create radial slots on the external surface of the component.
The tool rotates at the same speed as the component with opposite direction.
APPARECCHIO CONTROPOLIGONATORE PER SPACCO SFERE SPHERE CUTTING ATTACHMENT
704-849-9209 [email protected] 701 Matthews-Mint Hill Rd Matthews, NC
28105