UNI EN ISO 9902-6:2009
-
Upload
marco-loia -
Category
Documents
-
view
40 -
download
1
description
Transcript of UNI EN ISO 9902-6:2009
NORMAEUROPEA
Pagina IUNI EN ISO 9902-6:2009
© UNI Riproduzione vietata. Tutti i diritti sono riservati. Nessuna parte del presente documentopuò essere riprodotta o diffusa con un mezzo qualsiasi, fotocopie, microfilm o altro, senzail consenso scritto dell’UNI.
www.uni.com
UNIEnte Nazionale Italianodi UnificazioneVia Sannio, 220137 Milano, Italia
UNI EN ISO9902-6
SETTEMBRE 2009
Macchinario tessileProcedura per prove di rumorositàParte 6: Macchinario per la fabbricazione di tessuti
Textile machineryNoise test code Part 6: Fabric manufacturing machinery
La norma, insieme alla UNI EN ISO 9902-1, specifica le condizionidi montaggio, funzionamento e misurazione richieste per lamisurazione, la dichiarazione e la verifica del rumore emessodal macchinario per la fabbricazione di tessuti.
TESTO INGLESE
La presente norma è la versione ufficiale in lingua inglese dellanorma europea EN ISO 9902-6 (edizione marzo 2001), dell’aggior-namento A1 (edizione marzo 2009) e tiene conto delle correzioniintrodotte il 20 maggio 2009, il 3 giugno 2009 e il 29 luglio 2009.
La presente norma sostituisce la UNI EN ISO 9902-6:2003, cherimane tuttavia in vigore fino al 28 dicembre 2009.
ICS 17.140.20; 59.120.30
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
© UNI Pagina IIUNI EN ISO 9902-6:2009
Le norme UNI sono elaborate cercando di tenere conto dei punti di vista di tutte le partiinteressate e di conciliare ogni aspetto conflittuale, per rappresentare il reale statodell’arte della materia ed il necessario grado di consenso.Chiunque ritenesse, a seguito dell’applicazione di questa norma, di poter fornire sug-gerimenti per un suo miglioramento o per un suo adeguamento ad uno stato dell’artein evoluzione è pregato di inviare i propri contributi all’UNI, Ente Nazionale Italiano diUnificazione, che li terrà in considerazione per l’eventuale revisione della norma stessa.
Le norme UNI sono revisionate, quando necessario, con la pubblicazione di nuove edizioni odi aggiornamenti. È importante pertanto che gli utilizzatori delle stesse si accertino di essere in possessodell’ultima edizione e degli eventuali aggiornamenti. Si invitano inoltre gli utilizzatori a verificare l’esistenza di norme UNI corrispondenti allenorme EN o ISO ove citate nei riferimenti normativi.
PREMESSA NAZIONALELa presente norma costituisce il recepimento, in lingua inglese,della norma europea EN ISO 9902-6 (edizione marzo 2001) edell’aggiornamento A1 (edizione marzo 2009 con correzioni del20 maggio 2009, 3 giugno 2009 e 29 luglio 2009), che assumonocosì lo status di norma nazionale italiana.
La presente norma è stata elaborata sotto la competenza dellaCommissione Tecnica UNISicurezza
La presente norma è stata ratificata dal Presidente dell’UNI ed èentrata a far parte del corpo normativo nazionale il 3 settembre 2009.
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
EN ISO 9902-6:2001/A1
March 2009
ICS 59.120.30; 17.140.20
English Version
Textile machinery - Noise test code - Part 6: Fabricmanufacturing machinery - Amendment 1 (ISO 9902-
6:2001/Amd 1:2009)
Matériel pour l'industrie textile - Code d'essai acoustique -Partie 6: Machines de production des étoffes -
Amendement 1 (ISO 9902-6:2001/Amd 1:2009)
Textilmaschinen - Geräuschmessverfahren - Teil 6:Maschinen zur Hertsellung textiler Flächengebilde -
Änderung 1 (ISO 9902-6:2001/Amd 1:2009)
This amendment A1 modifies the European Standard EN ISO 9902-6:2001; it was approved by CEN on 12 March 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of thisamendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning suchnational standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under theresponsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the officialversions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATIONC O M I T É E U R O P É E N D E N O R M A LI S A T I O NEUR OP ÄIS C HES KOM ITEE FÜR NOR M UNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.
Ref. No. EN ISO 9902-6:2001/A1:2009: E
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
EN ISO 9902-6:2001/A1:2009 (E)
2
Contents Page
Foreword ..............................................................................................................................................................3�
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC ..............................................................................................4�
Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC ..........................................................................................5�
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
EN ISO 9902-6:2001/A1:2009 (E)
3
Foreword
This document (EN ISO 9902-6:2001/A1:2009) has been prepared by Technical Committee ISO/TC 72 "Textile machinery and machinery for dry-cleaning and industrial laundering" in collaboration with Technical Committee CEN/TC 214 "Textile machinery and accessories", the secretariat of which is held by SNV.
This Amendment to the European Standard EN ISO 9902-6:2001 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by December 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directives.
For relationship with EC Directives, see informative Annexes ZA and ZB, which are integral parts of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 9902-6:2001/Amd 1:2009 has been approved by CEN as a EN ISO 9902-6:2001/A1:2009 without any modification.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
EN ISO 9902-6:2001/A1:2009 (E)
4
Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 98/37/EC. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with Essential Requirement 1.7.4 f) of that Directive and associated EFTA regulations. WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
EN ISO 9902-6:2001/A1:2009 (E)
5
Annex ZB (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with Essential Requirement 1.7.4.2 u) of that Directive and associated EFTA regulations. WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Reference numberISO 9902-6:2001/Amd.1:2009(E)
© ISO 2009
INTERNATIONAL STANDARD
ISO9902-6
First edition2001-03-15
AMENDMENT 12009-03-15
Textile machinery — Noise test code — Part 6: Fabric manufacturing machinery
AMENDMENT 1
Matériel pour l'industrie textile — Code d'essai acoustique —
Partie 6: Machines de production des étoffes
AMENDEMENT 1
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001/Amd.1:2009(E)
PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT © ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.
ISO copyright office Case postale 56 � CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001/Amd.1:2009(E)
© ISO 2009 – All rights reserved iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 9902-6:2001 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 8, Safety requirements for textile machinery.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001/Amd.1:2009(E)
© ISO 2009 – All rights reserved 1
Textile machinery — Noise test code —
Part 6: Fabric manufacturing machinery
AMENDMENT 1
Page 1, Normative references
Delete the year of publication for the following references:
ISO 3743-1
ISO 3744
ISO 3746
ISO 3747
ISO 9614-1
Page 1, Normative references
Replace the reference to ISO 5247:1983 with the following:
ISO 5247 (all parts), Textile machinery and accessories — Weaving machines
Page 1, Normative references
Replace the reference to ISO 7839:1984 with the following:
ISO 7839:2005, Textile machinery and accessories — Knitting machines — Vocabulary and classification
Page 2, Normative references
Delete the year of publication for the following references:
ISO 9614-2
ISO 11201
ISO 11202
ISO 11203
ISO 11204
Page 2, Normative references
Add the following reference:
ISO 9902-1:2001/Amd.1:2009, Textile machinery — Noise test code — Part 1: Common requirements
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001/Amd.1:2009(E)
2 © ISO 2009 – All rights reserved
Page 3, 5.2
Replace the first sentence with the following:
See 5.2 of ISO 9902-1:2001, as amended by ISO 9902-1:2001/Amd.1:2009.
Page 4, 6.2.3
Replace the title of 6.2.3 with the following:
6.2.3 Flatbed knitting machine, straight-bar knitting machine and flat warping knitting machine
Page 4, 6.2.4
Replace the title of 6.2.4 with the following:
6.2.4 Circular weaving and circular knitting machine
Page 4, Figure 3
Replace the title of Figure 3 with the following:
Figure 3 — Circular weaving and circular knitting machine
Page 6, Clause 12
Replace the first paragraph with the following:
See Clause 12 of ISO 9902-1:2001, as amended by ISO 9902-1:2001/Amd.1:2009.
Page 11, Table 3
In the first column entitled “Machine family”, delete the entire row entitled “Circular flatbed knitting machine”.
Page 12, Table 3
In the first column entitled “Machine family”, replace “Warp knitting and Raschel machines” with “Flat warp knitting machines”. Add the letter “L” to the sixth column entitled “Very large machinery”.
Page 13, Table 3
In the first column entitled “Machine family”, replace “Cotton machines” with “Straight-bar knitting machines”.
Delete the entire second row entitled “Stitch bonding machines (knitting)”.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
EN ISO 9902-6
March 2001
ICS 17.140.20; 59.120.01
English version
Textile machinery - Noise test code - Part 6: Fabricmanufacturing machinery (ISO 9902-6:2001)
Matériel pour l'industrie textile - Code d'essai acoustique -Partie 6: Machines de production des étoffes (ISO 9902-
6:2001)
Textilmaschinen - Geräuschmessverfahren - Teil 6:Maschinen zur Herstellung textiler Flächengebilde (ISO
9902-6:2001)
This European Standard was approved by CEN on 15 March 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATIONC O M I T É E U R O P É E N D E N O R M A LI S A T I O NEUR OP ÄIS C HES KOM ITEE FÜR NOR M UNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.
Ref. No. EN ISO 9902-6:2001 E
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Page 2EN ISO 9902-6:2001
Foreword
The text of the International Standard ISO 9902-6:2001 has been prepared by Technical Committee ISO/TC72 "Textile machinery and machinery for dry-cleaning and industrial laundering" in collaboration withTechnical Committee CEN/TC 214 "Textile machinery and machinery for dry-cleaning and industrial laundry",the secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by September 2001, and conflicting national standards shall bewithdrawn at the latest by September 2001.
This European Standard has been prepared under a mandate given to CEN by the European Commissionand the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal,Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 9902-6:2001 was approved by CEN as a European Standardwithout any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).
Attention is drawn to the possibility that some of the elements of this International Standard may be thesubject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
This first edition of ISO 9902-6, together with ISO 9902-1, ISO 9902-2, ISO 9902-3, ISO 9902-4,ISO 9902-5 and ISO 9902-7, cancels and replaces ISO 9902:1993, which has been technically revised.
ISO 9902 consists of the following parts, under the general title Textile machinery - Noise test code:
- Part 1: Common requirements- Part 2: Spinning preparatory and spinning machinery- Part 3: Nonwoven machinery- Part 4: Yarn processing, cordage and rope manufacturing machinery- Part 5: Weaving and knitting preparatory machinery- Part 6: Fabric manufacturing machinery- Part 7: Dyeing and finishing machinery
Annex ZA of this part of ISO 9902 is for information only.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Page 3EN ISO 9902-6:2001
Annex ZA(normative)
Normative references to international publications with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other publications.These normative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publications apply tothis European Standard only when incorporated in it by amendment or revision. For undated references thelatest edition of the publication referred to applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by (mod.), the relevantEN/HD applies.
Publication Year Title EN YearISO 3743-1 1994 Acoustics Determination of sound power levels of
noise sources Engineering methods for small,movable sources in reverberant fields Part 1:Comparison method in hard-walled test rooms
EN ISO 3743-1 1995
ISO 3744 1994 Acoustics Determination of sound power levels ofnoise sources using sound pressure Engineeringmethod in an essentially free field over a reflectingplane
EN ISO 3744 1995
ISO 3746 1995 Acoustics Determination of sound power levels ofnoise sources using sound pressure Survey me-thod using an enveloping measurement surfaceover a reflecting plane
EN ISO 3746 1995
ISO 3747 2000 Acoustics Determination of sound power levels ofnoise sources using sound pressure Comparisonmethod for use in situ
EN ISO 3747 2000
ISO 9614-1 1993 Acoustics Determination of sound power levels ofnoise sources using sound intensity Part 1:Measurement at discrete points
EN ISO 9614-1 1995
ISO 9614-2 1996 Acoustics Determination of sound power levels ofnoise sources using sound intensity Part 2:Measurement by scanning
EN ISO 9614-2 1996
ISO 11201 1995 Acoustics Noise emitted by machinery and equip-ment Measurement of emission sound pressurelevels at a work station and at other specified posi-tions Engineering method in an essentially freefield over a reflecting plane
EN ISO 11201 1995
ISO 11202 1995 Acoustics Noise emitted by machinery and equip-ment Measurement of emission sound pressurelevels at a work station and at other specified posi-tions Survey method in situ
EN ISO 11202 1995
ISO 11203 1995 Acoustics Noise emitted by machinery and equip-ment Determination of emission sound pressurelevels at a work station and at other specified posi-tions from the sound power level
EN ISO 11203 1995
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Page 4EN ISO 9902-6:2001
ISO 11204 1995 Acoustics Noise emitted by machinery and equip-ment Measurement of emission sound pressurelevels at a work station and at other specified posi-tions Method requiring environmental corrections
EN ISO 11204 1995
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Page 5EN ISO 9902-6:2001
Annex ZB(informative)
Clauses of this European Standard addressing Essential Requirements or other provisionsof EU Directives
This European Standard has been prepared under a mandate given to CEN by the European Commissionand the European Free Trade Association and supports essential requirements of following EU directive(s).
Machinery Directive 98/37/EC, amended by Directive 98/79/EC.
WARNING: Other requirements and other EU Diectives may be applicable to the product(s) falling within thescope of this standard.
Compliance with this standard provides one means of conforming with specific essential requirements of theDirective(s) concerned and associated EFTA regulations.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Reference numberISO 9902-6:2001(E)
© ISO 2001
INTERNATIONALSTANDARD
ISO9902-6
First edition2001-03-15
Textile machinery — Noise test code —
Part 6:Fabric manufacturing machinery
Matériel pour l’industrie textile — Code d'essai acoustique —
Partie 6: Machines de production des étoffes
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall notbe edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading thisfile, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in thisarea.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameterswere optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely eventthat a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronicor mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member bodyin the country of the requester.
ISO copyright officeCase postale 56 � CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail [email protected] www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved iii
Contents Page
Foreword.....................................................................................................................................................................iv
1 Scope ..............................................................................................................................................................1
2 Normative references ....................................................................................................................................1
3 Terms and definitions ...................................................................................................................................2
4 Defining the test object .................................................................................................................................2
5 Sound power level determination ................................................................................................................2
6 Emission sound pressure level determination...........................................................................................3
7 Installation and mounting conditions..........................................................................................................6
8 Operating conditions.....................................................................................................................................6
9 Measurement uncertainties ..........................................................................................................................6
10 Information to be recorded ...........................................................................................................................6
11 Information to be reported............................................................................................................................6
12 Declaration and verification of noise emission values..............................................................................6
Bibliography ..............................................................................................................................................................14
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
iv © ISO 2001 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISOmember bodies). The work of preparing International Standards is normally carried out through ISO technicalcommittees. Each member body interested in a subject for which a technical committee has been established hasthe right to be represented on that committee. International organizations, governmental and non-governmental, inliaison with ISO, also take part in the work. ISO collaborates closely with the International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 9902 may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 9902-6 was prepared by Technical Committee ISO/TC 72, Textile machinery andmachinery for dry-cleaning and industrial laundering, Subcommittee SC 8, Safety requirements for textilemachinery.
This first edition of ISO 9902-6, together with ISO 9902-1, ISO 9902-2, ISO 9902-3, ISO 9902-4, ISO 9902-5 andISO 9902-7, cancels and replaces ISO 9902:1993, which has been technically revised.
ISO 9902 consists of the following parts, under the general title Textile machinery — Noise test code:
— Part 1: Common requirements
— Part 2: Spinning preparatory and spinning machinery
— Part 3: Nonwoven machinery
— Part 4: Yarn processing, cordage and rope manufacturing machinery
— Part 5: Weaving and knitting preparatory machinery
— Part 6: Fabric manufacturing machinery
— Part 7: Dyeing and finishing machinery
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
INTERNATIONAL STANDARD ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 1
Textile machinery — Noise test code —
Part 6:Fabric manufacturing machinery
1 Scope
This part of ISO 9902, taken together with ISO 9902-1, specifies the mounting, operating and measuring conditionsrequired for the measurement, declaration and verification of noise emitted by fabric manufacturing machinery. It isapplicable to engineering (grade 2) and survey (grade 3) methods, in accordance with the International Standardsto which it makes normative reference.
This part of ISO 9902 covers the different types of weaving and knitting machines defined in ISO 5247 andISO 7839, respectively. It is applicable to full-width weaving machines with shuttles, with rigid, telescopic or flexiblerapiers, with projectiles, and to those with weft insertion by hydraulic (waterjet) or by pneumatic (airjet) nozzle. It isalso applicable to narrow fabric weaving machines with weft insertion by shuttles or needles, to other weavingmachines of the multi-phase and circular weaving types, and to Jacquard machines. This part of ISO 9902 isapplicable to knitting machinery including circular knitting, flat bed knitting, warp knitting, Raschel, cotton (flat weftweaving) and stitch bonding machines.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions ofthis part of ISO 9902. For dated references, subsequent amendments to, or revisions of, any of these publicationsdo not apply. However, parties to agreements based on this part of ISO 9902 are encouraged to investigate thepossibility of applying the most recent editions of the normative documents indicated below. For undatedreferences, the latest edition of the normative document referred to applies. Members of ISO and IEC maintainregisters of currently valid International Standards.
ISO 3743-1:1994, Acoustics — Determination of sound power levels of noise sources — Engineering methods forsmall, movable sources in reverberant fields — Part 1: Comparison method in hard-walled test rooms.
ISO 3744:1994, Acoustics — Determination of sound power levels of noise sources using sound pressure —Engineering method in an essentially free field over a reflecting plane.
ISO 3746:1995, Acoustics — Determination of sound power levels of noise sources using sound pressure —Survey method using an enveloping measurement surface over a reflecting plane.
ISO 3747:2000, Acoustics — Determination of sound power levels of noise sources using sound pressure —Comparison method in situ.
ISO 5247:1983, Textile machinery and accessories — Weaving machines — Classification and vocabulary.
ISO 7839:1984, Textile machinery and accessories — Knitting machines — Classification and vocabulary.
ISO 9614-1:1993, Acoustics — Determination of sound power levels of noise sources using sound intensity —Part 1: Measurement at discrete points.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
2 © ISO 2001 – All rights reserved
ISO 9614-2:1996, Acoustics — Determination of sound power levels of noise sources using sound intensity —Part 2: Measurement by scanning.
ISO 9902-1:2001, Textile machinery — Noise test code — Part 1: Common requirements.
ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission soundpressure levels at a work station and at other specified positions — Engineering method in an essentially free fieldover a reflecting plane.
ISO 11202:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission soundpressure levels at a work station and at other specified positions — Survey method in situ.
ISO 11203:1995, Acoustics — Noise emitted by machinery and equipment — Determination of emission soundpressure levels at a work station and at other specified positions from the sound power level.
ISO 11204:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission soundpressure levels at a work station and at other specified positions — Method requiring environmental corrections.
3 Terms and definitions
For the purposes of this part of ISO 9902, the terms and definitions given in ISO 9902-1 apply.
4 Defining the test object
See Tables 1 to 3 of this part of ISO 9902 and clause 4 of ISO 9902-1:2001.
5 Sound power level determination
5.1 International Standards required for basic measurements
5.1.1 General
See 5.1 of ISO 9902-1:2001.
5.1.2 Determination by measuring sound intensity
Determination of the A-weighted sound power level, LWA, using sound intensity measurements shall be inaccordance with ISO 9614-1 (discrete points) or ISO 9614-2 (scanning).
5.1.3 Determination using emission sound pressure levels on a measurement surface
Determination of the A-weighted sound power level, LWA, by measurement of A-weighted emission sound pressurelevels on a prescribed measurement surface shall be in accordance with one of the following:
� ISO 3744,
� ISO 3747, or
� ISO 3746, but only where use of ISO 3744 or ISO 3747 is not practicable.
Where its conditions are met (e.g. in the case of small narrow fabric weaving machines or knitting machines),ISO 3743-1 provides an alternative method which may be used.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 3
5.2 Very large machines
See 5.2 of ISO 9902-1:2001. Very large machines are designated by the letter “L” in Tables 1 to 3 of this part ofISO 9902.
6 Emission sound pressure level determination
6.1 International Standards required for basic measurements
See 6.1 of ISO 9902-1:2001.
The A-weighted emission sound pressure level, LpA, shall be determined in accordance with one of the following:
� ISO 11201,
� ISO 11204, or
� ISO 11202, but only where use of ISO 11201 or 11204 is not practicable.
Where its conditions are met (e.g. in the case of small, narrow fabric weaving machines or knitting machines withprincipally omnidirectional sound radiation) and the sound power level has already been determined,ISO 11203:1995 (6.2.3) gives an alternative method which may be used, providing the distance from the machinesurface is 1 m.
6.2 Selection of work station and other specified positions
6.2.1 General
See 6.2 of ISO 9902-1:2001 and Tables 1 to 3 of this part of ISO 9902.
6.2.2 Weaving machinery other than circular and narrow fabric machines
For weaving machines that are not of the circular or narrow fabric type, select eight measurement positions, asshown in Figure 1, at a distance of 1 m and a height of 1,6 m above the floor or working platform. In areas wherespace is restricted, the measurement distance from the machine surface may be reduced to 0,5 m or 0,25 m (thisshall be reported and declared). Use the eight values measured at the defined positions to calculate LpA (see 6.1 ofISO 9902-1:2001). If the back of the machine is not accessible during operation with material, the first threepositions may be excluded.
Dimensions in metres
Key
1 Sley
A to H are the measurement positions.
Figure 1 — Weaving machines other than circular and narrow fabric machines
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
4 © ISO 2001 – All rights reserved
6.2.3 Knitting machinery other than circular machines, but including circular flat bed knitting machines
For flatbed knitting machines, warp knitting machines, Raschel machines and stitch-bonding machines (includingparticular warp knitting machines such as carpet warp knitting and cotton machines) with a maximum working widthof 8 m, select eight measurement positions, as shown in Figure 2, at a distance of 1 m and a height of 1,6 m abovethe floor or working platform. For larger machines, increase the number of positions such that the distance betweentwo adjacent positions does not exceed 3 m. Where access to the rear is prevented by the delivered yarn, omit themeasurement positions on the rear. Use the eight values measured at the defined positions to calculate LpA (see6.1 of ISO 9902-1:2001).
Dimensions in metres
A to H are the measurement positions.
Figure 2 — Knitting machines other than circular machines
6.2.4 Circular weaving and knitting machines
For circular weaving as well as circular knitting machines, select four measurement positions, as shown in Figure 3,at a distance of 1 m and a height of 1,6 m above the floor or working platform. Use the four values measured at thedefined positions to calculate LpA (see 6.1 of ISO 9902-1:2001).
Dimensions in metres
A to D are the measurement positions.
Figure 3 — Circular weaving and knitting machines
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 5
6.2.5 Narrow fabric weaving machines
For narrow fabric weaving machines, select a single measurement position, as shown in Figure 4, at a distance of1 m from the middle of the front of the machine and at a height of 1,6 m above the floor or working platform. Usethe value measured at this position to calculate LpA (see 6.1 of ISO 9902-1:2001).
Dimensions in metres
A is the measurement position.
Figure 4 — Narrow fabric weaving machines
6.2.6 Jacquard machines
For Jacquard machines, select eight measurement positions, as shown in Figure 5. Take two series ofmeasurements at a distance of 1 m from the centre of each side. The height of measurement positions 1 to 4 shallbe half the height of the frame, while the height of measurement positions 5 to 8 shall be that of the height of thecentreline of the Jacquard. Use the eight values to calculate LpA (see 6.1 of ISO 9902-1:2001).
Dimensions in metres
Key
1 Frame
2 Jacquard machine
A to H are the measurement positions.
Figure 5 — Jacquard machines
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
6 © ISO 2001 – All rights reserved
7 Installation and mounting conditions
See clause 7 of ISO 9902-1:2001.
8 Operating conditions
See clause 8 of ISO 9902-1:2001 and Tables 1 to 3 of this part of ISO 9902.
For weaving machines having two or more variable parameters, as an alternative to the method given in Table 1(see clause 8 of ISO 9902-1:2001), the noise emission values depending on speed and other variable parameters(e.g. width and number of heald frames) may be determined. In such cases, the values shall be reported anddeclared, preferably in tabular or graphical form, or by means of a correction factor, or both.
9 Measurement uncertainties
See clause 9 of ISO 9902-1:2001.
10 Information to be recorded
See clause 10 of ISO 9902-1:2001.
11 Information to be reported
See clause 11 of ISO 9902-1:2001. The information required to be reported includes that contained in Tables 1 to 3of this part of ISO 9902.
12 Declaration and verification of noise emission values
See clause 12 of ISO 9902-1:2001.
If the alternative given in clause 8 of this part of ISO 9902 is chosen, provide an explanation of how LpA and LWAcan be obtained from the table or graph, or, using the correction factor, for the specified values of the variableparameters. In addition, the uncertainties KpA and KWA shall be declared.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le1
—M
easu
rem
ent
con
dit
ion
sfo
rw
eavi
ng
mac
hin
ery
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
a
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Shu
ttle
wea
ving
mac
hine
sse
eN
otes
1an
d2
—a)
type
ofsh
edfo
rmat
ion
max
imum
wor
king
wid
thin
cent
imet
res
whe
reap
prop
riate
the
shut
tlebo
xch
ange
type
ofau
tom
atic
doffe
req
uipm
entf
orpi
rnw
indi
ng
type
ofhe
ald
fram
es(e
.g.m
ater
ial,
desi
gn)
L
for
pape
rfe
ltan
dca
rpet
see
6.2.
2w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
num
ber
ofhe
ald
fram
es
fabr
icda
ta
wor
king
wid
thus
edin
cent
imet
res
shut
tledi
men
sion
sin
mill
imet
res
shut
tlem
ass
ingr
ams
shut
tlem
ater
ial
type
and
mat
eria
lof
the
pick
er
type
and
mat
eria
lof
the
back
stop
Pro
ject
ilew
eavi
ngm
achi
nes
see
Not
es1
and
2
—a)
type
ofsh
edfo
rmat
ion
max
imum
wor
king
wid
thin
cent
imet
res
type
ofhe
ald
fram
es(e
.g.m
ater
ial,
desi
gn)
type
ofw
eft
yarn
supp
ly
—
see
6.2.
2w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
num
ber
ofhe
ald
fram
es
fabr
icda
ta
wor
king
wid
thus
edin
cent
imet
res
Rap
ier
wea
ving
mac
hine
sse
eN
otes
1an
d2
—a)
type
ofsh
edfo
rmat
ion
max
imum
wor
king
wid
thin
cent
imet
res
type
ofhe
ald
fram
es(e
.g.m
ater
ial,
desi
gn)
type
ofw
eft
yarn
supp
ly
—
see
6.2.
2w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
num
ber
ofhe
ald
fram
es
fabr
icda
ta
wor
king
wid
thus
edin
cent
imet
res
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 7UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le1(continued)
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
a
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Wea
ving
mac
hine
sw
ithw
efti
nser
tion
byno
zzle
see
Not
es1
and
2ai
rpr
epar
atio
nor
wat
erpr
epar
atio
n
a)
type
ofsh
edfo
rmat
ion
max
imum
wor
king
wid
thin
cent
imet
res
type
ofhe
ald
fram
es(m
ater
iald
esig
n)
type
ofw
eft
yarn
supp
ly
type
ofm
achi
ne(a
iror
wat
er)
—
see
6.2.
2w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
num
ber
ofhe
ald
fram
es
fabr
icda
ta
nozz
lepr
essu
rein
pasc
als
wor
king
wid
thus
edin
cent
imet
res
Mul
ti-ph
ase
wea
ving
mac
hine
sw
ithw
efti
nser
tion
byno
zzle
see
Not
e1
air
prep
arat
ion
a)
max
imum
wor
king
wid
thin
cent
imet
res
type
ofw
eft
yarn
supp
ly—
see
6.2.
2w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
fabr
icda
ta
air
pres
sure
inpa
scal
s
wor
king
wid
thus
edin
cent
imet
res
Nar
row
fabr
icw
eavi
ngm
achi
nes
see
Not
e1
Jacq
uard
mac
hine
with
harn
ess
—a)
type
ofsh
edfo
rmat
ion
max
imum
wor
king
wid
thin
cent
imet
res
type
ofhe
ald
fram
es
type
ofm
achi
ne(s
huttl
eor
need
lety
pe)
—
see
6.2.
5an
d6.
1w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
num
ber
ofhe
ald
fram
es
fabr
icda
ta
wor
king
wid
thus
edin
cent
imet
res
num
ber
ofpi
eces
Nar
row
fabr
icw
eavi
ngm
achi
nes
with
inte
grat
edJa
cqua
rdm
achi
ne
Jacq
uard
mac
hine
—a)
spec
ifica
tion
ofJa
cqua
rdm
achi
ne
max
imum
wor
king
wid
thin
cent
imet
res
—
see
6.2.
5an
d6.
1w
ithm
ater
ial
spee
din
wef
tin
sert
ions
per
min
ute
num
ber
ofJa
cqua
rden
ds
wor
king
wid
thus
edin
cent
imet
res
fabr
icda
ta
num
ber
ofpi
eces
ISO 9902-6:2001(E)
8 © ISO 2001 – All rights reserved
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le1(continued)
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
a
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Circ
ular
wea
ving
mac
hine
sS
eeN
ote
1
—a)
max
imum
diam
eter
inm
illim
etre
s
num
ber
ofro
tatin
gsh
uttle
s
num
ber
ofdo
bby
mec
hani
sms
—
see
6.2.
4w
ithou
tmat
eria
l
80%
ofth
em
axim
umdi
amet
erin
mill
imet
res
mac
hine
spee
din
revo
lutio
nspe
rm
inut
e
—
NO
TE
1T
hete
stob
ject
isth
ew
eavi
ngm
achi
nefit
ted
with
equi
pmen
tfo
rfe
edan
dde
liver
yof
mat
eria
l(e
.g.
war
pbe
ams,
clot
hbe
ams)
,bu
tex
clud
ing
war
pcr
eels
and
free
stan
ding
equi
pmen
tfo
rcl
oth-
take
-up
(e.g
.fab
ricw
indi
ngm
achi
ne,f
oldi
ngm
achi
ne).
NO
TE
2In
mos
tcas
es,n
oise
test
sof
wea
ving
mac
hine
san
dJa
cqua
rdm
achi
nes
will
have
tobe
cond
ucte
dse
para
tely
.How
ever
,in
orde
rto
beab
leto
oper
ate
the
wea
ving
mac
hine
with
mat
eria
l,a
dobb
yha
ving
the
min
imum
ofhe
ald
fram
esca
nbe
used
tosi
mul
ate
the
Jacq
uard
mac
hine
.Kno
wle
dge
ofth
efin
alin
stal
latio
nco
nfig
urat
ion
can
then
enab
leca
lcul
atio
nof
the
nois
eem
issi
onof
the
com
bine
dw
eavi
ngm
achi
nean
dJa
cqua
rdm
achi
ne.
aH
owev
er,s
uch
equi
pmen
tmay
bene
cess
ary
for
runn
ing
the
mac
hine
with
mat
eria
l.
Tab
le2
—M
easu
rem
ent
con
dit
ion
sfo
rJa
cqu
ard
mac
hin
es
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Jacq
uard
mac
hine
sm
echa
nica
llyor
elec
tron
ical
lyco
ntro
lled
—
harn
ess
and
driv
e(s
eeN
ote
2,T
able
1)
b)
max
imum
num
ber
ofho
oks
desc
riptio
nof
the
shed
geom
etry
—
see
6.2.
6w
ithou
tmat
eria
l
liftp
atte
rn1:
1
hook
load
inup
per
posi
tion
5N
spee
din
wef
tin
sert
ions
per
min
ute
—
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 9UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le3
—M
easu
rem
ent
con
dit
ion
sfo
rkn
itti
ng
mac
hin
ery
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Circ
ular
knitt
ing
mac
hine
sin
tegr
ated
cree
lre
mot
ecr
eel
a)
nom
inal
diam
eter
ofth
em
achi
nein
mill
imet
res
type
ofdr
ive
(e.g
.el
ectr
ichy
drau
lic)
type
ofm
achi
ne(n
eedl
ecy
linde
ror
cam
box
ring
rota
ting)
type
ofne
edle
s(la
tch
type
orco
mpo
und)
num
ber
ofne
edle
carr
iers
pitc
hin
mill
imet
res
(gau
geE
acco
rdin
gto
ISO
8188
)
num
ber
ofne
edle
carr
iers
(sec
tions
)
type
offa
bric
take
-up
and
take
-dow
n(d
off)
devi
ce
type
ofne
edle
sele
ctor
ifap
prop
riate
.
with
/with
outy
arn
chan
ger
with
orw
ithou
tfan
s
—
see
6.2.
4an
d6.
1w
ithm
ater
ial
patte
rn:m
achi
new
ith1
need
leca
rrie
r:R
L;m
achi
new
ith2
need
leca
rrie
rs:R
R
80%
to85
%of
the
max
imum
oper
atio
nsp
eed
inre
volu
tions
perm
inut
e
clos
edho
ods
orco
vers
max
imum
num
ber
ofne
edle
san
dkn
ittin
gsy
stem
s
—
mat
eria
ldat
a
ISO 9902-6:2001(E)
10 © ISO 2001 – All rights reserved
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le3(continued)
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Fla
tbed
knitt
ing
mac
hine
sin
tegr
ated
cree
lre
mot
ecr
eel
a)
max
imum
wor
king
wid
thin
mill
imet
res
max
imum
oper
atio
nsp
eed
inm
etre
spe
rse
cond
num
ber
ofne
edle
carr
iers
num
ber
ofca
rria
ges
num
ber
ofsy
stem
spe
rca
rria
ge
need
lepi
tch
inm
illim
etre
s(g
auge
Eac
cord
ing
toIS
O81
88)
—
see
6.2.
3w
ithm
ater
ial
patte
rn:m
achi
new
ith1
need
leca
rrie
r:R
L,m
achi
new
ith2
orm
ore
need
leca
rrie
rs:R
R
wor
king
wid
th:8
0%
to85
%of
the
max
imum
wor
king
wid
th
80%
to85
%of
the
max
imum
oper
atio
nsp
eed
clos
edho
ods
orco
vers
max
imum
num
ber
ofne
edle
san
dkn
ittin
gsy
stem
s
—
mat
eria
ldat
a
Circ
ular
flatb
edkn
ittin
gm
achi
nes
cree
l
—a)
oper
atio
nsp
eed
inm
etre
spe
rse
cond
nom
inal
wor
king
wid
thin
mill
imet
res
num
ber
ofne
edle
carr
iers
num
ber
ofca
rria
ges
num
ber
ofsy
stem
spe
rca
rria
ge
need
lepi
tch
inm
illim
etre
s(g
auge
Eac
cord
ing
toIS
O81
88)
—
see
6.2.
3w
ithm
ater
ial
patte
rn:R
R
80%
+5
%of
the
max
imum
oper
atio
nsp
eed
clos
edho
ods
orco
vers
max
imum
num
ber
ofne
edle
san
dkn
ittin
gsy
stem
s
—
mat
eria
ldat
a
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 11UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le3(continued)
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
War
pkn
ittin
gan
dR
asch
elm
achi
nes
inte
grat
edfe
edin
gan
dde
liver
yde
vice
s
wef
tins
ertio
nde
vice
rem
ote
feed
ing
devi
ce
a)
max
imum
oper
atio
nsp
eed
inm
esh
row
spe
rmin
ute
max
imum
oper
atio
nw
idth
inm
illim
etre
s
need
lepi
tch
inm
illim
etre
s(g
auge
Eac
cord
ing
toIS
O81
88)
num
ber
ofne
edle
carr
iers
type
ofne
edle
s
type
and
num
ber
ofgu
ide
bars
type
offe
ed(e
.g.
inte
grat
edbe
am,
free
stan
ding
beam
fram
e,cr
eel)
type
ofbe
amre
gula
tor
type
ofw
eft
inse
rtio
n
type
ofJa
cqua
rdm
achi
ne
num
ber
ofne
edle
san
dsi
nker
s
with
orw
ithou
tsu
ctio
nde
vice
—
see
6.2.
3w
ithou
tmat
eria
lop
erat
ion
spee
din
mes
hro
ws
perm
inut
e
—
ISO 9902-6:2001(E)
12 © ISO 2001 – All rights reserved
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Tab
le3(continued)
Test
obj
ectd
efin
itio
n(s
eecl
ause
4)O
per
atin
gco
nditi
ons
(see
ISO
9902
-1:2
001,
clau
se8)
Mac
hin
efa
mily
Equ
ipm
enti
nclu
ded
fort
hete
stif
appl
icab
le
Equ
ipm
ente
xclu
ded
from
the
test
Mac
hine
conf
igur
atio
n(s
eeIS
O99
02-1
:200
1,cl
ause
4)
Des
ign
feat
ures
tobe
repo
rted
Ver
yla
rge
mac
hin
ery
L(5
.2)
Wor
kst
atio
n(s
ee6.
2)P
resc
ribed
para
met
ers
Var
iabl
epa
ram
eter
sP
aram
eter
sto
bere
port
ed
Cot
ton
mac
hine
s
——
a)
max
imum
oper
atio
nsp
eed
inm
esh
row
spe
rm
inut
e
max
imum
wor
king
wid
thin
mill
imet
res
need
lepi
tch
inm
illim
etre
s
type
ofpa
ttern
ing
devi
ce
num
ber
ofne
edle
carr
iers
wid
thof
need
leca
rrie
rsin
mill
imet
res
—
see
6.2.
3w
ithm
ater
ial
oper
atio
nsp
eed
inm
esh
row
spe
rm
inut
e
—
Stit
chbo
ndin
gm
achi
nes
(kni
tting
)in
tegr
ated
cree
lre
mot
efe
edin
gde
vice
a)
max
imum
oper
atio
nsp
eed
inm
esh
row
spe
rm
inut
e
max
imum
wor
king
wid
thin
mill
imet
res
type
offe
ed(e
.g.
war
pbe
am)
num
ber
ofgu
ide
bars
need
lepi
tch
inm
illim
etre
s
laps
with
orw
ithou
tgla
ssch
oppe
r
—
see
6.2.
3w
ithou
tmat
eria
lop
erat
ion
spee
din
mes
hro
ws
per
min
ute
—
aH
owev
er,s
uch
equi
pmen
tmay
bene
cess
ary
for
runn
ing
the
mac
hine
with
mat
eria
l.
ISO 9902-6:2001(E)
© ISO 2001 – All rights reserved 13UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
ISO 9902-6:2001(E)
14 © ISO 2001 – All rights reserved
Bibliography
[1] ISO 8188:1986, Textile machinery and accessories — Pitches of knitting machine needles.
UNI EN ISO 9902-6:2009
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .
Riproduzione vietata - Legge 22 aprile 1941 Nº 633 e successivi aggiornamenti.UNIEnte Nazionale Italianodi UnificazioneVia Sannio, 220137 Milano, Italia
Norma contenuta ne l l 'Opera "S icurezza de l lavoro ne i cant ier i " ex accordo de l 01/05/2012 t ra UNI e Wol ters K luwer I ta l ia .R iproduz ione v ie ta ta .