IP10 CLI Libre

8/9/2019 IP10 CLI Libre

1/23

FibeAir ®

IP-10

CLI(Command Line Interface)

User Guide

Part ID: BM-0134-0

Doc ID: DOC-00018394 Rev a.01

May 2008


2/23

Notice

This document contains information that is proprietary to Ceragon Networks Ltd.

No part of this publication may be reproduced, modified, or distributed without prior writtenauthorization of Ceragon Networks Ltd.

This document is provided as is, without warranty of any kind.

Registered TradeMarks

Ceragon Networks® is a registered trademark of Ceragon Networks Ltd.

FibeAir ® is a registered trademark of Ceragon Networks Ltd.

CeraView® is a registered trademark of Ceragon Networks Ltd.

Other names mentioned in this publication are owned by their respective holders.

TradeMarksCeraMap

TM, PolyView

TM, EncryptAir

TM, ConfigAir

TM, CeraMon

TM, EtherAir

TM, and MicroWave

Fiber TM

, are trademarks of Ceragon Networks Ltd.

Other names mentioned in this publication are owned by their respective holders.

Statement of Conditions

The information contained in this document is subject to change without notice.

Ceragon Networks Ltd. shall not be liable for errors contained herein or for incidental orconsequential damage in connection with the furnishing, performance, or use of thisdocument or equipment supplied with it.

Information to User

Any changes or modifications of equipment not expressly approved by the manufacturercould void the user’s authority to operate the equipment and the warranty for such equipment.

Copyright © 2008 by Ceragon Networks Ltd. All rights reserved.

Corporate Headquarters

Ceragon Networks Ltd.24 Raoul Wallenberg St.Tel Aviv 69719, IsraelTel: 972-3-645-5733Fax: 972-3-645-5499Email: [email protected]

www.ceragon.com

European Headquarters

Ceragon Networks (UK) Ltd.4 Oak Tree Park, Burnt Meadow RoadNorth Moons Moat, Redditch,Worcestershire B98 9NZ, UKTel: 44-(0)-1527-591900Fax: 44-(0)-1527-591903Email: [email protected]

North American Headquarters

Ceragon Networks Inc.10 Forest Avenue,Paramus, NJ 07652, USATel: 1-201-845-6955Toll Free: 1-877-FIBEAIRFax: 1-201-845-5665

Email: [email protected]

APAC Headquarters

Ceragon Networks (HK) Ltd. Singapore ROLevel 34 Centennial Tower3 Temasek AvenueSingapore 039190Tel - + 65 6549 7886

Fax: +65 6549 7011


3/23

Contents

General .......................................................................................................... 1

Getting Started.............................................................................................. 2

Command Groups......................................................................................... 5

CLI Commands.............................................................................................. 8

CLI Command Parameters ..........................................................................11


4/23

FibeAir ® IP-10 CLI Guide 1

General

This guide explains how to work with the FibeAir ® IP-10 Command Line Interface (CLI).

The CLI is used to perform IP-10 configuration and obtain system statistical and performance information.

Using the CLI, you can perform configuration operations for single IP-10 units, as well as configure several

IP-10 units in a single batch command.

Access Rights

IP-10 CLI access is granted for the following user groups:

Viewer This user only has read-only access. The user can only view parameters and their values, not

modify them.Operator This user has read-write access. The user can read parameters and their values, and modify

them. However, this user cannot add or remove other users.

Admin This user has read-write access. The user can read parameters and their values, modify them,and add/remove other users.

Technician This user has read-write access to the CLI, as well as access to a bridge-specific CLI shell.

User access is controlled by the system administrator and configured via the Management command group

(shown in the Command Groups section).


5/23


Getting Started

To log in to the CLI:

1. Power on your PC.

2. Make sure that your PC is connected to the management port on the front panel of the IP-10 unit.

3. For a first-time login, use the following:

User: admin

Password: admin

Note: When using the Hyper Terminal, you should set the terminal speed (in your PC terminal

configuration) to 155200 kpbs. In addition, it is recommended to select the VT-100 terminal type and set the

terminal size to 24 rows, 80 columns.

Getting HelpOnce you are logged in, you can go to a main command group and its sub groups, type the command you

want, and press Tab twice for a list of possible parameter values.

In addition, you can type a command and then type a question mark (?) for location-specific information for

the command. For example, for the set command, typing set ? and pressing Enter will display a list of

optional parameters and a help line.

Wherever you are in the command tree, you can obtain a list of available commands by typing Help or ?.

The commands that are available are different for each location in the CLI tree and the type of user.

Basic Commands

The following basic commands are available when you first log in, if you belong to the Operator user group:

ls list entitiesget get parameterset set parameterhelp helpcd change directoryexit exit CLIlogout logout from CLIcli-ver cli versioncls clear screenwrite write the current switch configuration to the configuration fileshow-tree show entity treefind search for a string in the parameter name and information fieldslsp list entity parameters and commands

In addition, you can use the up/down arrow keys, or the “q” key, when the word “END” appears at the end

of the screen.


6/23


Finding Commands

At any point in the CLI tree, a quick way to find a command is to type find string , and press Enter.For string you can type any word that you think is relevant for a command.

For example, if you type find user, and press Enter, you would get a list of commands relating to "user", as

follows:

1) management/mng-services/mng-software/proxy-user User name passed to the ...2) management/mng-services/users/add-user Add user 3) management/mng-services/users/delete-user Delete user 4) management/mng-services/users/show-users Show users

Command Example

The following example shows how you can find a command within a sub-group, and then execute thecommand. The example starts with the lsp (list parameters) command, and ends with the activation of an

interface loopback test.

-----------------------------------------------

IP-10:/> cd diagnostics/loopback/radio-loopback/

IP-10:/diagnostics/loopback/radio-loopback> lsp

*********** configuration ********

timeout rw Loopback timeout in minutes

*********** statuses *************

counter ro Loopback time left

if-loopback rw IF loopback activation

rfu-rf-loopback rw RFU RF Loopback Enable Command

rfu-if-loopback rw RFU IF Loopback Enable Command

IP-10:/diagnostics/loopback/radio-loopback> set timeout 2

IP-10:/diagnostics/loopback/radio-loopback> set if-loopback

off on

IP-10:/diagnostics/loopback/radio-loopback> set if-loopback on

Caution: This action affects traffic.

The may cause permanent loss of Ethernet traffic & wayside.

Consider disabling or physically disconnecting the Ethernet ports of the IDM and

Wayside before the loopback activation.

Are you sure? (yes/no):yes

IP-10:/diagnostics/loopback/radio-loopback>

-----------------------------------------------

Important!

Note that bridge related commands need to be followed by a “write” command to be saved.

Otherwise, the commands will not be saved following a reset in the system.


7/23


Viewing the Command Tree

At any location within the command group structure, you can type show-tree and press Enter for a list of all

the commands in the group you are currently in.

The following list appears when you type show-tree.


8/23


Command Groups

The command groups that appear when you log in include the following:

Management

Platform

Radio

Interfaces

Diagnostics

Some groups include sub groups that enable setup operations relevant to that category.

The following illustrations show the trees of each main group.

Management

Management


9/23


Platform

Radio


10/23


Interfaces

Diagnostics


11/23


CLI Commands

The following table lists the commands you can use in each command group and sub group.

Note that when you enter a group or sub group, you can type a command and then press the Tab key twice

(or type a question mark) for a list of values relevant to that command.

Command Group Command Description

alarm-current show Show current alarms

bridge qos-show-ip-pbit-val Show IP pbits to queue allocation

bridge qos-show-vlan-priority Show QoS VLAN Priorities

bridge qos-show-vlan-tag-pbit-val Show VLAN tag pbits to queue allocation

bridge show-eth-statistics Show Ethernet Statistics

bridge show-ports-status Show status of all ports

bridge show-running-config Show current switch operating configuration

bridge show-vlan-info Show VLAN database information

bridge vlan Add, remove or modify values associated with asingle VLAN

cfg-service set-to-default Set to default

eth-port qos-show-policer-classes Show policer classes

eth-port qos-show-vlan-pbits-prio-remap Show VLAN Pbits priority remap

eth-port set-allowed-vlans Set allowed VLANs

eth-port show-allowed-vlans Show allowed VLANs

eth-port show-port-status Show port status

event-log clear Clear log

event-log show Show log


12/23


Command Group Command Description

idc-board reset-idc-hw Reset the IDC - cold (HW) reset

mate-idu copy-to-mate-cmd Copy to mate command

mate-idu create-copy-to-mate-nack-list-cmd

Create copy to mate nack list command

mate-idu manual-switch-cmd Manual switch command

mng-protocols status-show Show Management Protocols status

mng-snmp status-show Show SNMP status

mng-software download Download all relevant packages from remoteserver (without installation)

mng-software kernel-upgrade Upgrade Linux kernel

mng-software package-install Install new package (like SW patch) withoutexisting version installed

mng-software package-rollback Package rollback (downgrade to older version)

mng-software package-uninstall Uninstall SW package (recommended for patchremoval)

mng-software show-packages Show SW package information

mng-software upgrade Upgrade all installed packages or requestedpackage

mng-software verify-packages Verify installed packages

mstp msti-vid VLAN ID to be associated to instance

mstp show-msti-vid Show VLAN IDs associated to instance

pm-service clear-entire-pm Clear entire PM

remote-idu remote-cold-reset Reset the remote IDC - cold (HW) reset

rmon clear-all Clear RMON statistics from all ports

rmon clear-port Clear RMON statistics from a specific port


13/23


14/23


CLI Command Parameters

The following table lists the parameters you can use in the command groups and sub groups.

CommandGroup

Paremeter Description

alarm-current current-alarm-table System Alarm Current table indexed by time and quasi-sequential number

alarm-current most-severe Most severe alarm

alarm-current sequence-count Current alarm counter

bridge customer-l2protocol Customer L2 protocols (STP, LACP, GMRP, GVRP, MMRP,MVRP, DOT1X) tunneling

bridge ethernet-application Ethernet application bridge forward-time Forwarding delay time in seconds

bridge hello-time Hello time in seconds

bridge management-type Management type

bridge max-age Maximum ageing time in seconds

bridge max-hops Maximum hops the BPDU will be valid

bridge msti-bridge-priority Bridge priority for each defined MST instance

bridge priority Bridge priority

bridge qos-ip-precedence-val IP precedence IP pbits value

bridge qos-ip-tos-tc-pbits-option IP TOS/TC pbits options

bridge stp-protocol Spanning-tree protocol e1t1-port admin Enable/Disable the port

e1t1-port cable-length T1 cable length

e1t1-port interface-type Interface type

e1t1-port line-loopback Line loopback

e1t1-port line-pm-15 Line PM 15 minutes monitoring

e1t1-port line-pm-24 Line PM 24 hours monitoring

e1t1-port oper-status Operational status

e1t1-port port-curr-ber E1/T1 port current BER

e1t1-port priority Dynamic allocation priority

ethernet gbe-mute-override GbE mute override eth-port actual-duplex Actual duplex

eth-port actual-ethernet-rate Actual ethernet rate

eth-port admin Enable/Disable the port

eth-port auto-negotiation Auto negotiation

eth-port bad-octets-rcv Bad octets received

eth-port brdc-pkts-rcv Broadcast packets received

eth-port brdc-pkts-sent Broadcast packets sent

eth-port collisions Collisions

eth-port connector-type Connector type

eth-port deferred Deferred

eth-port duplex Half/Full duplex

eth-port ethernet-rate Ethernet rate (mbps)


15/23


CommandGroup


eth-port evc-name EVC name

eth-port excess-collision-drop Excess Collision Frame

eth-port flow-control Flow Control

eth-port fragments-pkts Fragments Packets

eth-port functionality-led Functionality LED

eth-port functionality-led.blink blink attribute

eth-port good-octets-rcv Good octets received

eth-port good-octets-sent Good octets sent

eth-port in-discards In Discards

eth-port in-fcs-err In FCS Error

eth-port in-filtered In Filtered

eth-port in-pause In Pause

eth-port in-rx-err In receive error eth-port interface-index Interface index

eth-port interface-type Interface type

eth-port in-uni-casts In Uni-Cast

eth-port jabber-pkts Jabber Packets

eth-port late-collision-detect Late Collision Detect

eth-port learning Learning admin

eth-port management-auto-negotiation

Management port auto negotiation

eth-port management-capacity Management port capacity

eth-port management-duplex Management port duplex eth-port

management-ethernet-rate

Management port Ethernet rate (Mbps)

eth-port management-only Management only

eth-port management-port-admin Port's admin

eth-port management-vlan Management VLAN id

eth-port mc-pkts-rcv Mc packets received

eth-port mc-pkts-sent Mc packets sent

eth-port msti-port-path-cost Path cost for each defined MST instance

eth-port msti-port-priority Interface priority for each defined MST instance

eth-port multiple-collision-frame Multiple Collision Frame

eth-port oper-status Operational status eth-port out-fcs-err Out FCS error

eth-port out-filtered Out filtered

eth-port out-pause Out pause

eth-port out-uni-casts Out Uni-Cast

eth-port oversize-pkts Oversize packets

eth-port path-cost Path cost

eth-port pkts-1024-max-octets Number of packets with size equal or greater than 1024 octets

eth-port pkts-128-255-octets Number of packets with size between 128 and 255 octets


eth-port pkts-512-1023-octets Number of packets with size between 512 and 1023 octets eth-port pkts-64-octets Number of packets with size equal or smaller to 64 octets


16/23


CommandGroup



eth-port priority Port's priority

eth-port protection-only Protection only

eth-port protection-port-admin Port's admin

eth-port qos-classifier-criteria Classifying criteria

eth-port qos-egress-shaper Egress shaper

eth-port qos-egress-shaper-rate

Egress shaper rate. The value should be in steps. The stepsare: 64K - for values less than 1Mbps. 1M - for values between1Mbps and 100Mbps. 10M - for values between 100Mbps and1000Mbps (GbE Ports Only)

eth-port qos-marker QoS marker

eth-port qos-policer-action Policer action

eth-port qos-policer-cbs

eth-port qos-policer-class-name Policer class name associate to this policer

eth-port qos-policer-name Policer name associated to this port

eth-port qos-policer-rate Policer rate

eth-port qos-policer-type Policer type

eth-port qos-prio-override-port Priority override port

eth-port qos-scheduling-scheme Scheduling scheme

eth-port qos-vlan-pbits-prio-remap VLAN pbits priority remap

eth-port role Port's role

eth-port rstp-edge-port Enable as edge port

eth-port rstp-link-type Link type

eth-port single-collision-frame Single Collision Frame

eth-port state Port's state

eth-port type Port's type

eth-port undersize-pkts Undersize packets

eth-port vlan Default VLAN ID

eth-port wayside-auto-negotiation Wayside auto negotiation

eth-port wayside-capacity Wayside Port Capacity

eth-port wayside-duplex Wayside half/full Duplex

eth-port wayside-ethernet-rate Wayside Ethernet port rate (Mbps)

eth-port wayside-only Wayside only

eth-port wayside-port-admin Port's admin event-log log-count log counter

event-log log-table System event log table indexed by time and quasi-sequentialnumber

fpga fw-version FPGA FW Version

framer link-id Link ID

framer oper-status Operational status

framer radio-ber Radio BER Status

framer radio-excessive-ber-threshold

Radio Excessive BER Threshold Configuration

framer radio-pm-15min-interval Radio 15 minutes interval performance monitor

framer radio-pm-24hour-interval Radio 24 hours interval performance monitor

framer radio-signal-degrade- Radio Signal Degrade Threshold Configuration


17/23


CommandGroup


threshold

idc-board idu-led IDU LED

idc-board idu-led.blink blink attribute

idc-board measurement-system Measurement system

idc-board protection-led Protection LED

idc-board protection-led.blink blink attribute

idc-board radio-led Radio LED

idc-board radio-led.blink blink attribute

idc-board remote-led Remote LED

idc-board remote-led.blink Blink attribute

idc-board rfu-led RFU LED

idc-board rfu-led.blink blink attribute

idc-board system-up-time System up time (in hundredths of second) idc-board temperature Temperature

idc-board version IDC's Version

inventory board-modules Board Modules

inventory board-sub-type The sub-type of the board

inventory board-type The type of the board

inventory chain-firmware The firmware of the chain

inventory chain-hardware-features The hardware features of the chain

inventory chain-sub-type The sub-type of the chain

inventory chain-type The type of the chain

inventory comments Text description about the board inventory company-name Company name

inventory date-code Date of board testing (number of seconds from 1/1/1970)

inventory firmware Firmware

inventory hardware Hardware

inventory hass-number Number of hass testing

inventory hw-supported-bit-bate HW supported bit bate

inventory idc-firmware The firmware of the IDC

inventory idc-hardware-features The hardware features of the IDC

inventory idc-sub-type The sub-type of the IDC

inventory

idc-type

The type of the IDC inventory license-demo-timer Number of hour left for license demo mode

inventory license-register System license features

inventory modem-firmware The firmware of the modem

inventory modem-hardware-features

The hardware features of the modem

inventory modem-sub-type The sub-type of the modem

inventory modem-system-rate The frequency of the clock for the PVG

inventory modem-type The type of the modem

inventory mux-firmware The firmware of the MUX

inventory mux-hardware-features The hardware features of the MUX

inventory mux-sub-type The sub-type of the MUX inventory mux-type The type of the MUX


18/23


CommandGroup


inventory num-of-10-100-1000-interfaces

Number of 10/100/1000 interfaces

inventory num-of-fe-interfaces Number of fast Ethernet interfaces inventory num-of-sfp-interfaces Number of SFP interfaces

inventory num-of-tdm-interfaces Number of TDM interfaces

inventory num-of-working-hours Counter of working hours of the board

inventory part-number Part number of the application in the board

inventory product-name Product name

inventory rx-iq-delay-high-rate-systems

RX IQ delay offset for high rate systems

inventory rx-iq-delay-low-rate-systems

RX IQ delay offset for low rate systems

inventory serial-number The serial number of the board

inventory spare1 Spare 1



inventory tx-iq-delay-high-rate-systems

Tx IQ delay offset for high rate systems

inventory tx-iq-delay-low-rate-systems

Tx IQ delay offset for low rate systems

inventory type-of-tdm-interfaces Type of TDM interfaces

inventory xc-firmware The firmware of the XC

inventory xc-hardware-features The hardware features of the XC

inventory xc-sub-type The sub-type of the XC inventory xc-type The type of the XC

ip-address default-gateway Default gateway

ip-address hw-address Hw address

ip-address ip-address Unit management IP address

ip-address ip-v6-address IPv6 address

ip-address subnet-mask Unit subnet mask

license acm-license

license capacity-name rate name

license demo-admin

license demo-timer Time left for license demo mode (in hours) license license-code

license license-type

license switch-application-license

line-loopback counter Loopback time left

line-loopback line-loopback Line loopback

line-loopback timeout Loopback timeout in minutes (0 for unlimited)

mate-idu copy-to-mate-nack-list

mate-idu excessive-ber-switch-enable

mate-idu mate-ip-address

mate-idu mate-mac-address


19/23


CommandGroup


mate-idu protection-admin

mate-idu protection-force-switch

mate-idu protection-lockout

mate-idu protection-mode

mate-idu protection-role

mate-idu remote-ber-adjustment-time

mate-idu remote-lof-adjustment-time

mate-idu remote-sd-adjustment-time

mate-idu sd-switch-enable

mng-protocols telnet-admin Telnet administrative state

mng-protocols telnet-status Telnet service status

mng-protocols web-admin Web administrative state

mng-protocols web-status Web service status

mng-snmp snmp-admin SNMP administrative state

mng-snmp snmp-read-community SNMP read community

mng-snmp snmp-status SNMP service status

mng-snmp snmp-version SNMP version

mng-snmp snmp-write-community SNMP write community

mng-snmp trap-admin Enable/Disable sending SNMP traps

mng-snmp trap-community SNMP trap community mng-snmp trap-group-filter SNMP trap group filter

mng-snmp trap-heartbeat How often (in minutes) a trap heartbeat is sent to the manager(0 to disable)

mng-snmp trap-manager Address of manager to which SNMP traps will be sent

mng-snmp trap-name Text to name or comment the manager

mng-snmp trap-port Manager port to which traps are sent (default 162)

mng-snmp trap-severity-filter Filter which traps are sent to the manager by their severity.

mng-software application-versions list of individual application packages and their versions

mng-software common-version common version identifying the whole application packagesset

mng-software proxy-password Password passed to the proxy

mng-software proxy-url Proxy URL

mng-software proxy-user User name passed to the proxy

mng-software server-login Remote server login

mng-software server-password Remote server password

mng-software server-url Remote SW Update server URL where SW updates reside

mng-software status-download last SW download status

mng-software status-install last SW installation status

modem clear-counters Clear accumulated counters

modem defected-blocks Defected blocks

modem ldpc-decoder-stress LDPC decoder stress

modem mse MSE


20/23


CommandGroup


mrmc connected-rfu-grade Actual connected rfu grade information

mrmc

current-acm-adaptive-

profile Current ACM adaptive profile Information mrmc current-bitrate Current bit rate Information

mrmc current-profile Current profile Information

mrmc current-qam Current QAM Information

mrmc loaded-script-description Loaded script description Information

mrmc loaded-script-version Modem script version Information

mrmc max-adaptive-acm-profile Maximum adaptive ACM profile Information

mrmc max-available-tdm-interfaces

Max available TDM interface information

mrmc max-chosen-bitrate Max chosen bitrate information

mrmc min-adaptive-acm-profile Min adaptive ACM profile Information mrmc mrmc-pm-15min-interval MRMC 15 minutes interval performance monitor

mrmc mrmc-pm-24hour-interval MRMC 24 hours interval performance monitor

mrmc mrmc-script MRMC script Information

mrmc mse-threshold MSE threshold Information

mrmc occupied-bandwidth Occupied bandwidth Information

mrmc operation-mode Operation mode Information

mrmc rfu-chosen-grade RFU chosen grade information

mstp region-name Name of the MST region

mstp revision-number Revision number for configuration information

networking auto-negotiation Management port auto negotiation

networking capacity Management port capacity

networking duplex Management port duplex

networking ethernet-rate Management port Ethernet rate (Mbps)

networking number-of-ports Number of management ports

networking type How management data is passed

networking vlan Management VLAN id

platform system-contact-person System contact person

platform system-description System description

platform system-location System location

platform system-name System name

port-group exber-threshold Excessive BER threshold Information port-group line-code Line code Information

port-group pdh-led PDH LED color

port-group pdh-led.blink blink attribute

port-group sd-threshold Space Diversity threshold

radio-loopback counter Loopback time left

radio-loopback if-loopback IF loopback activation

radio-loopback rfu-if-loopback RFU IF Loopback Enable Command

radio-loopback rfu-rf-loopback RFU RF Loopback Enable Command

radio-loopback timeout Loopback timeout in minutes

remote-idu remote-atpc-enable Remote ATPC Enable/Disable configuration remote-idu remote-atpc-ref-rx-level Remote ATPC reference Rx level configuration


21/23


CommandGroup


remote-idu remote-communication Remote Communication Status

remote-idu remote-default-gateway Remote IDU default gateway

remote-idu remote-force-max-tx-level Force remote Max transmit level configuration

remote-idu remote-force-mute-tx Force remote Mute transmitter configuration

remote-idu remote-ip-address Remote IDU IP address

remote-idu remote-link-id Remote IDU Link ID

remote-idu remote-management-type Remote Management type Status

remote-idu remote-management-vlan Remote Management VLAN ID configuration

remote-idu remote-most-severe-alarm

Remote Most Severe Alarm Status

remote-idu remote-rx-level Remote Rx level status

remote-idu remote-subnet-mask Remote IDU subnet mask

rfic if-loopback IF loopback activation rfu atpc-enable RFU ATPC Enable/Disable

rfu atpc-ref-rx-level RFU ATPC Reference Rx Level

rfu band RFU band status

rfu cable-tilt RFU cable tilt status

rfu communication-status RFU communication to remote unit status

rfu delay-calibration RFU delay calibration configuration

rfu delay-calibration-operation

RFU delay calibration command

rfu delay-calibration-result RFU delay calibration result status

rfu fpga-version-number RFU FPGA version number

rfu hardware-reset RFU Reset Hardware Command

rfu ifc-support RFU IFC support status

rfu if-loopback-support RFU IF loopback support status

rfu internal-download-counter

RFU internal download counter status

rfu internal-download-status RFU internal download status

rfu log-enable RFU Log Enable/Disable Configuration

rfu log-interval RFU Log interval configuration, in seconds

rfu lo-sense RFU lo sense status

rfu max-bandwidth RFU maximum bandwidth status

rfu max-rx-freq RFU maximum Rx frequency status rfu max-tx-freq RFU maximum Tx frequency status

rfu max-tx-level RFU Maximum Transmit Level Configuration

rfu min-bandwidth RFU minimum bandwidth status

rfu min-rx-freq RFU minimum Rx frequency status

rfu min-tx-freq RFU minimum Tx frequency status

rfu mse-forward RFU MSE forward command

rfu mute-tx RFU Mute Transmitter

rfu part-number RFU part number

rfu pm-15min-interval RFU 15 minutes interval performance monitor

rfu pm-15min-interval-combined RFU 15 minutes interval combined performance monitor

rfu pm-15min-interval- RFU 15 minutes interval diversity performance monitor


22/23


CommandGroup


diversity

rfu pm-24hour-interval RFU 24 hours interval performance monitor

rfu pm-24hour-interval-combined

RFU 24 hours interval combined performance monitor

rfu pm-24hour-interval-diversity

RFU 24 hours interval diversity performance monitor

rfu pmax RFU Pmax status

rfu pmin RFU Pmin status

rfu pm-rx-level-threshold-1 RFU Performance Monitoring Rx Level Threshold 1Configuration

rfu pm-rx-level-threshold-2 RFU Performance Monitoring Rx Level Threshold 2Configuration

rfu pm-tx-level-threshold

RFU Performance Monitoring Tx Level Threshold

Configuration rfu power-supply-status RFU Power Supply Status

rfu predistortion-support RFU Predistortion support status

rfu rf-loopback-support RFU RF loopback support status

rfu rfu-address RFU address status

rfu rfu-class RFU class status

rfu rfu-if-loopback RFU IF Loopback Enable Command

rfu rfu-installation RFU installation status

rfu rfu-mode RFU Mode configuration

rfu rfu-rf-loopback RFU RF Loopback Enable Command

rfu rfu-type Type of connected RFU rfu rsl-connector-source RFU RX level connector source configuration

rfu rx-freq RFU Rx frequency configuration

rfu rx-freq-local-remote RFU Change Rx Frequency Local Remote Command

rfu rx-level RFU Receive Level Status

rfu rx-level-combined RFU Rx level combined status

rfu rx-level-diversity RFU Rx level diversity

rfu serial-number RFU serial number

rfu software-version-number RFU software version number

rfu standard-organization RFU standard organization

rfu synthesizer-status RFU synthesizer

rfu temp-in-celsius RFU Temperature In Celsius

rfu temp-in-celsius-pa RFU temperature in Celsius on PA

rfu temp-in-fahrenheit RFU Temperature In Fahrenheit

rfu tx-freq RFU Tx Frequency Configuration

rfu tx-freq-local-remote RFU Change Tx Frequency Local Remote Command

rfu tx-level-status RFU Transmit Level

rfu tx-rx-freq-separation RFU Tx Rx frequency separation

rfu unfaded-rsl RFU Unfaded Rx Level Configuration

rfu-sw-upload internal-download-action RFU Internal Download Of Software/firmware/tables ActionCommand

rfu-sw-upload internal-download-counter

RFU internal download counter status


23/23

CommandGroup


rfu-sw-upload internal-download-status RFU internal download status

time-service time-and-date Time and date format: Day-Mon-Year,hour:min:sec

wayside admin Enable/Disable Wayside channel

wayside auto-negotiation Wayside auto negotiation

wayside capacity Wayside channel capacity

wayside duplex Wayside half/full Duplex

wayside ethernet-rate Wayside Ethernet port rate (Mbps)

IP10 CLI Libre

Documents

Transcript of IP10 CLI Libre