Brochure Rugby AI ver 2 · 2015-07-30 · Complete lamp can replace traditional high pressure...
Transcript of Brochure Rugby AI ver 2 · 2015-07-30 · Complete lamp can replace traditional high pressure...
TENNIS
LED Lighting Division
BBTel
Centri sportiviindoor e outdoor
Soluzioni professionalid’illuminazione a Led
info@bbtel. it
BBTelLED Lighting Division
info@bbtel. it
Soluzioni professionali d’illuminazione a Led
• Risparmio energetico dal 30% fino al 70%.• Totale assenza di manutenzione per lungo periodo.• Maggiore uniformità della luce.• Accensione e spegnimento immediato.• Gestione in remoto istantanea o programmata dell’intensità luminosa da 0% a 100%.• Miglior controllo dell’abbagliamento.• Nessuna dispersione di luce.• Controllo dell’inquinamento luminoso.• Resa cromatica elevata.• Grande flessibilità ottica.
• Assenza di emissione di raggi UV.• Ridotta emissione di calore.• Alta resistenza agli urti accidentali.• Totale assenza di metalli pesanti.• Maggiore stabilità di prestazione nel tempo.• Alimentazione in bassa tensione.• Totale assenza di flickering e stabilità del colore.• Cablaggi ridotti per portare energia al campo.• Minore richiesta di potenza per la fornitura di energia elettrica.
I vantaggi della tecnologia LED
La progettazione di un buon impianto di illuminazione è significativa non solo per il risparmio economico che ne consegue, ma anche per la qualità visiva che comporta.L’avvento della tecnologia LED ha notevolmente accentuato questi aspetti, introducendo nuovi parametri di risparmio energetico che hanno rivoluzionato quella che era la comune idea di luce.• Importante riduzione dei consumi con miglioramento dell’intensità luminosa.• Accensione e spegnimento immediato dell’impianto con possibilità di regolazione dell’intensità luminosa in remoto.• Miglioramento del confort e delle condizioni di gioco e di allenamento.• Minor affaticamento visivo con conseguente aumento dei tempi di reazione.• Migliore percezione delle distanze.I molteplici vantaggi apportati dall’uso della tecnologia LED sono sintetizzabili nei seguenti punti:
BBTel garantisce il progetto con un'adeguata intensità e uniformità nella distribuzione della luce ed è in grado di trovare il giusto punto di equilibrio fra le esigenze di illuminazione degli atleti e quelle degli spettatori.
A tutto questo si unisce un’elevatissima efficienza energetica, un’ importante riduzione del costo dell’energia, della manutenzione e un allungamento della vita media dell’impianto.
Grazie ad uno staff tecnico altamente specializzato, esperienza ventennale ed attrezzature dedicate, abbiamo selezionato un’ampia gamma di prodotti di illuminazione a LED. BBTel è in grado di progettare e realizzare sistemi di illuminazione per impianti sportivi di ogni genere sia da interno che da esterno.
Attraverso un software dedicato di simulazione dell’impianto e mediante l’ausilio di proiettori a LED professionali,
SCHEDA BBTEL-TN500TENNIS 500 LUX
1000W 500W Progetto conforme alla norma UNI 12193 - Luce e illuminazione.Illuminazione di installazioni sportive.La norma è la versione ufficiale in lingua inglese della norma europea EN 12193 (edizione dicembre 2007). La norma fornisce i valori per la progettazione ed il controllo dell'illuminazione delle installazioni sportive in termini di illuminamento, uniformità, limitazione dell'abbagliamento e proprietà di colore delle sorgenti di luce. Tutti i requisiti sono intesi come requisiti minimi. La norma fornisce inoltre i metodi di misurazione di tali valori. Essa precisa anche le limitazioni della posizione degli apparecchi d’illuminazione nelle applicazioni particolari, per la limitazione dell'abbagliamento.
AA
AASimulazione softwareProgetto: TN500 Lux
0 75 150 225 300 375 450 525 600 Lux
Illuminamento medio510 LuxUniformità Emin/Emed0,80Fattore di manutenzione0,80
1(4; 1)
(2; 8)
(4; 10)
(5; 11)
(2; 11)
8; 6; 9
2
-11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10
X(m)
21-
11-
01-9-
8-7-
6-5-
4-3-
2-1-
01
23
45
67
89
011
121
)m(
Y
AA
AA
480
531
540
519
489
463
450
449
455
467
487
513
539
544
508
509
583
612
592
550
507
479
468
481
512
546
578
599
584
524
511
599
648
642
597
538
497
480
497
543
592
631
634
595
516
509
597
650
654
612
551
503
486
503
551
612
654
650
597
509
516
595
634
631
592
543
497
480
497
538
597
642
648
599
511
524
584
599
578
546
512
481
468
479
507
550
592
612
583
509
508
544
539
513
487
467
455
449
450
463
489
519
540
531
480
53
4
PuntamentiProiettore X Y N
1 4.00 1.002 2.00 8.003 2.00 11.004 4.00 10.005 5.00 11.00
ProiettoreHigh Power Mast
DriverHLG-240H(2PCS)
LedXTE - XML2
Flusso luminoso (lm)33.000
Numero pali4
Altezza dei pali (m f.t.)9
Numero proiettori20
Numero proiettori per palo5
BBTelLED Lighting Division
info@bbtel. it
Soluzioni professionali d’illuminazione a Led
SCHEDA BBTEL-TN200TENNIS 200 LUX
Progetto conforme alla norma UNI 12193 - Luce e illuminazione.Illuminazione di installazioni sportive.La norma è la versione ufficiale in lingua inglese della norma europea EN 12193 (edizione dicembre 2007). La norma fornisce i valori per la progettazione ed il controllo dell'illuminazione delle installazioni sportive in termini di illuminamento, uniformità, limitazione dell'abbagliamento e proprietà di colore delle sorgenti di luce. Tutti i requisiti sono intesi come requisiti minimi. La norma fornisce inoltre i metodi di misurazione di tali valori. Essa precisa anche le limitazioni della posizione degli apparecchi d’illuminazione nelle applicazioni particolari, per la limitazione dell'abbagliamento.
AA
A ASimulazione softwareProgetto: TN200 Lux
Illuminamento medio205 LuxUniformità Emin/Emed0,80Fattore di manutenzione0,80
1
2
3
(4; 4)
(3; 7)
(4; 10)
8; 7; 9
-11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10
X(m)
21-
11-
01-9-
8-7-
6-5-
4-3-
2-1-
01
23
45
67
89
011
121
)m(
Y
158
185
204
214
217
209
199
192
195
203
210
213
208
194
167
174
211
238
249
244
227
211
203
209
223
239
247
241
218
180
178
221
249
259
253
231
210
202
210
229
250
258
251
225
181
180
223
249
258
252
231
209
199
209
231
252
258
249
223
180
181
225
251
258
250
229
210
202
210
231
253
259
249
221
178
180
218
241
247
239
223
209
203
211
227
244
249
238
211
174
167
194
208
213
210
203
195
192
199
209
217
214
204
185
158
0 50 1 00 1 05 200 2 05 300 350 400 Lux
Numero pali4
Altezza dei pali (m f.t.)9
Numero proiettori12
Numero proiettori per palo3
PuntamentiProiettore X Y N
1 4.00 4.002 3.00 7.003 4.00 10.00
ProiettoreHigh Power Mast
DriverHLG-150H-36A(2PCS)
LedCREE-XPE
Flusso luminoso (lm)21.000
500W 300W
BBTelLED Lighting Division
info@bbtel. it
Soluzioni professionali d’illuminazione a Led
BBTelLED Lighting DivisionLED Lighting DivisionSoluzioni professionali d’illuminazione a Led
info@bbtel . it
500W SIZE Unit:mm
POWER (W) 500
VOLTAGE (V) 42 / 30
CURRENT (mA) 10800 / 15000
CHIP MODEL XTE
LED QTY (pcs.) 224 / 220
WAY OF SERIES/PARALLEL 2x(8P 14S) / 2x(11P 10S)
PCB'S SIZE (mm) 205x67x2 / Ø110x2
POWER SUPPLY HLG-240H-42A(2PCS)
500W SIZE Unit:mm
POWER (W) 1000 1000
VOLTAGE (V) 33 30
CURRENT (mA) 27000 30000
CHIP MODEL XTE XML2
LED QTY (pcs.) 440 280
WAY OF SERIES/PARALLEL 4x(10P 11S) 4x(7P 10S)
PCB'S SIZE (mm) 310x106x2 310x106x2
POWER SUPPLY HLG-240H-36A(4PCS) HLG-240H-30A(4PCS)
500W SIZE Unit:mm
1000W SIZE Unit:mm
500W projector • lncomparable heatsink housing:1000W projector • lncomparable heatsink housing:
Complete lamp can replace traditional high pressure sodium lamp over 2000W. It can instant start, and has long life span, low consumption of energy, and polluting free. It can be widely used at the stadium, golf course, wharf, square.etc.
HIGH POWER MAST LED
BBTelLED Lighting DivisionLED Lighting DivisionSoluzioni professionali d’illuminazione a Led
info@bbtel . it
Protection rate IP65By using water-proof connector and silicon rubber sealing, the protection rate can achieve IP65, meeting the requirement for harsh, tough environment.
Respirator designWaterproof design,eliminating mist, avoiding codensation, improving quality, extending the life span.
PROFESSIONAL DESIGN, FULL PROTECTION
Flake type high purity aluminum reflectors by anodic oxidation and polishing processing, the optimization of lighting performance at the same time, effectively reduce excessive light and glare, 25°, 45°, 60°, 90°, 100° angles such as selection, and has a narrow angle of 30°, wide Angle 90° and narrow angle 60°, wide Angle 90° square reflectors optional, satisfy the professional light distribution, adapted to different occasions.
500W projector • lncomparable heatsink housing:
Inside high purity aluminum reflector is processed with anodization and polishing, optimize the lighting performance and restrain the dizzy light and spill light. Square reflectors is also available: 10°x90°and 50°x90°. Meet the requirement of professional light distribution and can be used at different places.
1000W projector • Professional light distribution
45° Light distribution curve 45° Average illumination curve
90° Light distribution curve 90° Average illumination curve
10° 90° Light distribution curve 10° 90° Average illumination curve
50° 90° Light distribution curve 50° 90° Average illumination curve
• 500W • Superior performance
Using heat pipe cooling technology, riveting fins group create unparal-leled heat engine. With 25°, 45° to 60°, 90°, 100° a variety of light distribution, can be widely used in sports venues, construction, cranes, port, airport, large factory building, square and other places of need high power LED lighting.
• 1000W • Professional light distribution
By riveting the heat pipe to the fins, the heatsink (housing) having excellent thermal performance. Square reflectors 10°x90° and 50°x90°, meet the requirement of professional light distribution, and can restrain the dazzle light and spill light effectively. With the 4mm tempered glass, no need for extra shield; High pressure diecasting process made this reflector strong. It has been processed by electrophoretic paint, and passed 200 hours salt spray test. Waterproof rate:IP65.
HIGH POWER MAST LED
BBTelLED Lighting DivisionLED Lighting DivisionSoluzioni professionali d’illuminazione a Led
info@bbtel . it
500W kit show:1000W kit show:
500W features:
PATENTED ZIPPED-FIN TECHNOLOGY Each fins to maintain equal spacing and tight fit, form a whole, effectively enhance the fins fastness, with the minimum weight to achieve maximum cooling area.
3-D HEAT DISSIPATIONEach fins are distributed parallel relative to hollow out holes, or so appear a convection of air duct, and fins clearance form three-dimensional heat dissipation, send out quantity of heat to the greatest extent.
HIGH PERFORMANCE HEAT PIPEHeat pipe by using the theory of heat transfer and refrigeration, rapid heat transfer properties of the medium to transfer heat quickly to the heat source, thermal capacity than any known metal.
PATENTED HDT TECHNOLOGYHigh efficient heatpipes contact the heat source directly, maxima the performance of the heat pipe to reach the cooling effect.
1000W features:
PATENTED ZIPPED-FIN TECHNOLOGYWith zipped-fin technology, the convection airflow is evenly distributed in the cooling fins, optimizing the cooling effect. The fins couple into the base of the heatsink tightly minimum the heat transfer resistance.
3-D HEAT DISSIPATIONThere are convection holes distributed on each fins allowing parallel direction airflow to maximum the cooling power.
HIGH PERFORMANCE HEAT PIPEThe heat pipe's principle is using the quick phases change of the liquid (medium) under vacuum condition which exchange the heat, the heat transfer rate is superior to any metal.
PATENTED HDT TECHNOLOGYHigh efficient heatpipes contact the heat source directly, maxima the performance of the heatpipe to reach the cooling effect.
500W projector • lncomparable heatsink housing:
By riveting the heatpipes to the fins, make the incomparable heatsink housing.The heat from the LEDs is transformed to the fins with massive dissipating area by the 12 x 08mm heatpipes, reducing the temperature of the LEDs rapidly and extending the lifespan.
1000W projector • lncomparable heatsink housing:
By riveting the heatpipes to the fins, make the incomparable heatsink housing.The heat from the LEDs is transformed to the fins with massive dissipating area by the 12 x 08mm heatpipes, reducing the temperature of the LEDs rapidly and extending the lifespan.
HIGH POWER MAST LED
BBTelLED Lighting DivisionLED Lighting DivisionSoluzioni professionali d’illuminazione a Led
info@bbtel . it
Structural drawing:
Luminaire photometric test report:
500W 300W
Pictures:
Features:
H100 H120 H150 H200 H300 H400 H500
200 pcs 260 pcs 300 pcs 380 pcs 196 pcs 280 pcs 280 pcs
100 W 120 W 150 W 200 W 300 W 400 W 500 W
7870 Lm±10% 10290 Lm±10% 12930 Lm±10% 16080 Lm±10% 23750 Lm±10% 30600 Lm±10% 33850 Lm±10%
5m 372 Lux 478 Lux 3676 Lux 1284 Lux 262 Lux 1396 Lux 4169 Lux
8m 145 Lux 186 Lux 919 Lux 320 Lux 65 Lux 155 Lux 463 Lux
15m 41 Lux 53 Lux 408 Lux 143 Lux 16 Lux 56 Lux 147 Lux
78.7 Lm/W 85.7 Lm/W 86.2 Lm/W 80.4 Lm/W 79.2 Lm/W 77.3 Lm/W 71.3 Lm/W
455*455*510 455*455*510 475*475*510 455*455*510 475*475*510 465*465*550 485*485*550
7,1 7,87 8,8 7,78 10,62 12 13
7,1 7,87 8,8 7,78 10,62 12 13
9,6 10,37 11,3 10,37 13,12 14,5 15,5
-25°C ÷ +50°C
50.000 h
IP65
Bare
AC 100V ÷ 270V
DC 30V ÷ 34V
> 0.95
Ra>75
2700 ÷ 3500K4000 ÷ 4500K5700 ÷ 6500
>6500K
25° / 60° / 90°
1 pcs
III
Alluminium + tempered glass
Back-lit
SMD-3020 CREE-XBD
Working Temperature
Product specification
Electrical parameters
Optical Parameters
Illumination
Package
Net Weight (Kg)
Gross Weight (Kg)
Lamp Type
Installation
IP Rate
Lifespan
Color Temperature
Beam Angle
Package Size (mm)
QTY of Package
Piece Weight (Kg)
CRI
ModelLighting Pattern
Material
LED Type
LED QTY
Power
Input Voltage
Output Voltage
Power Efficiency
Luminosity
Light Efficiency
Technical parameters:
HIGH POWER MAST LED