VARIAZIONI DA START S6 A START S6 XL
La centralina START-S6 XL, è dotata di un ingresso Costa in apertura. Tale ingresso è attivo solo in apertura e provoca
1 UTILIZZO DELL’INGRESSO COSTA IN AP - MORSETTO 23: N.C.
l’arresto e l’inversione in chiusura di entrambi i motori.
ATTENZIONE!!! Se l’ingresso non è utilizzato deve essere ponticellato con il comune.
Per regolare la forza dei motori si deve utilizzare il TRIMMER, e può essere impostata in qualsiasi momento anche durante il funzionamento dei motori.
2
REGOLAZIONE DELLA FORZA DEI MOTORI
1-ON STOP Disattiva l’ingresso STOP
2-ON FOTO in CH Disattiva l’ingresso FOTO in chiusura
3-ON FOTO in AP - CH Disattiva l’ingresso FOTO in apertura e in chiusura
4-ON PRELAMPEGGIO Attiva il prelampeggio
1
2
4
3
4
3 MODI DI FUNZIONAMENTOLa centrale dispone di una serie di microinterruttori che permettono di attivare varie funzioni al fine di rendere l’impianto più adatto alle esigenze dell’utilizzatore e per la sua maggior sicurezza.
La procedura di apprendimento codici radio viene fatta come per la ricevente R2A, premendo PON una volta si attiva l’apprendimento per il comando START, se si preme PON una seconda volta si attiva l’apprendimento per il comando PEDONALE.
E’ stata inserita la funzione di attivazione/disattivazione del controllo rolling completo. Per fare ciò si deve premere PON quando si è in apprendimento comando PEDONALE. Il LED M con rolling fisso esegue un solo lampeggio mentre con rolling completo ne esegue 2.
4 APPRENDIMENTO CODICI RADIO e CONTROLLO ROLLING
5 RESET - IMPOSTAZIONI DI FABBRICAE’ stata inserita la funzione di reset dei tempi e impostazioni ai valori di fabbrica. Per fare ciò premere PMENU quando si è in modo menù. Il Led dopo circa 10 secondi emette un accensione prolungata che indica l’avvenuta operazione.
PMENU 10 s
ACCENSIONE PROLUNGATA OPERAZIONE AVVENUTA
IN MODO MENU’
LED M
L’operazione è possibile anche a motore in fuzione
Se tali ingressi non vengono usati possono essere anche non ponticellati. Basta infatti utilizzare il relativo dip
1 3 alimentazione della centrale 230 Vac.
4 11 alimentazione motori 230 Vac e lampeggiante 230 Vac.
13 26tensioni di alimentazione degli accessori e ingressi servizi e sicurezze.
Pulsante P MENU:
gestione codici radio, regolazione della forza, incremento tempo di pausa.
Pulsante P ON o P A
pulsante funzione in programmazionepulsante start in funzionamento.
Pulsante P OFF o P B
pulsante funzione in programmazionepulsante pedonale in funzionamento.
Schema della centrale e dei collegamenti elettrici
230 Vac
230 Vac
230Vac
Lampeggiante
LampeggianteMOT 1 comune
MOT 1 apre
MOT 1 chiude
Lampeggiante o luce di cortesia 230 Vac
M
Motore 1 (pedonale) 230 Vac
Comune
StopStart
Foto A Chiude
12 Vac
Comune 0 Vac
24 Vac
Serratura 12 VacPedonale
Foto B Apre e Chiude
Ingresso Costa in AP - NCTest -24-
-23--22--21--20--19--18--17--16--15--14--13-
-8--7--6--5--4-
-3-
-1-
M
Motore 2 230 Vac
MOT 2 comuneMOT 2 apre
MOT 2 chiude -11--10--9-
Comune / Ant - -25-Ant + -26-
TXR
XTX
RX
N.O. N.C.N.O.N.O.
*
-2-
24 Vdc
Alim
entazione accessori
*
1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26
FUSE 160 mA
FUSE 4 A
Alimentazione accessori24 Vdc
Contatto SPIA
DIP disattiva gli ingressi FOTO- STOPapSTOPch e attiva prelampeggio
DIP
*
Serratura 12 Vac
Fotocellule attive sulla chiusura.
Fotocellule attive sia in chiusura che in apertura.
Collegare questo punto al morsetto n° 24 per avere il test sulle fotocellule.Altrimenti collegarlo al morsetto n°19.
*
Serratura 12 Vac
Fotocellule attive sulla chiusura.
Fotocellule attive sia in chiusura che in apertura.
Collegare questo punto al morsetto n° 24 per avere il test sulle fotocellule.Altrimenti collegarlo al morsetto n°19.
Variations of the operation of the control board START S6 XL
The control board START S6XL is equipped with an input for the edge in OP. This input is active in opening and in closing and causes the arrest and reversal of the engines.
1 INPUT FOR THE EDGE IN OP - Terminal board no. 23: N.C.
WARNING!!! If these inputs are not usedthe inputs must be jumper with common.
To regulate the power of the engines must use the TRIMMER, and can be set at any time even during engine operation.
2
FORCE ADJUSTMENT OF MOTORS
1-ON STOP Escludes the STOP input
2-ON FOTO in CL Escludes the FOTO input in closing
3-ON FOTO in OP - CL Escludes the FOTO input in opening and in closing
4-ON PREFLASHING Activate preflashing
1
2
4
3
4
3 MODE OF OPERATIONThe control board dispose of differents limit switches having a lot of functions that can be adapted to the exigences of the customerand to make a sure installation according to the security norms.
To learn a code make as follow: press button PON once for the START and press the button PON twice for PEDESTRIAN
This operation is necessary to activate or remove the key’s control and the rolling code counter. Press and eave the button PON when when you have to learn to control pedestrian. With Rolling fixed the LED M running a flashing otherwise the LED M performs two flashes.
4 TRANSMITTER’S LEARNING and ROLLING CODE’S CONTROL
5 RESET - FACTORY SETTINGSFor return to factory settings, push the PMENU in menu mode. After 10 seconds the led indicates the successful operation.
PMENU 10 s
SUCCESSFUL OPERATION
MENU MODE
LED M
Can be set at any time even during engine operation.
If these inputs are not used can not be jumper. You can just use the swithches.
WARNING
1 3 230 Vca power supply
4 11 230 Vca motor - power supply and 230 vca lamp
13 26 Power supply for accessoriesinputs and securities.
Pulsante P MENU:
Pulsante P ON o P A Button programming function
Pulsante P OFF o P B
Button programming function
Radio code managing, force regulation, LAMP pause time increasing.
CONTROL BOARD and CONNECTIONS
230 Vac
230 Vac
230Vac
Lamp
LampMOT 1 common
MOT 1 Open
MOT 1 Close
Lamps or courtesy light
M
Motor 1 (Pedestrian) 230 Vac
Common
StopStart
Foto A Close
12 Vac
Common 0 Vac
24 Vac
Lock 12 VacPedestrian
Foto B Open and Close
Mechanical edge input OP - NCTest -24-
-23--22--21--20--19--18--17--16--15--14--13-
-8--7--6--5--4-
-3-
-1-
M
Motor 2 230 Vac
MOT 2 commonMOT 2 open
MOT 2 close -11--10--9-
Common / Ant - -25-Ant + -26-
TXR
XTX
RX
N.O. N.C.N.O.N.O.
*
-2-
24 Vdc
Pow
er supply for accessories
*
1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26
FUSE 160 mA
FUSE 4 A
Power supply for accessories24 Vdc
Light
DIP controal board setting up
DIP
*
Lock 12 Vac
FOTO CL
FOTO OP-CL
Connect this point to terminal n° 24 for FOTO TESTOtherwise connect to terminal n°19.
*
Lock 12 Vac
FOTO CL
FOTO OP-CL
Connect this point to terminal n° 24 for FOTO TESTOtherwise connect to terminal n°19.