IMM SWAGING CHART · IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019 Emessa da: Mauro Di...
18
Tabella dei diametri di pressatura consigliati Chart of recommended swaging diameters IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019 Emessa da: Mauro Di Iorio Approvata da: lorenzo panzone Hypress 1SN; HyFreeze 1SN; Railway; TFD0011; TFDL011N; TFDE011 1SN R1AT EN 853 1SN - SAE 100 R1AT - ISO 1436 1SN Inserto Pelatura Ghiera Insert Skive Ferrule Dash Ø Pressatura Swaging Ø Dash Est. Ext. Int. Int. Pollici Inch Lung. Ins. Insert Depth Standard NO SKIVE 001C-03 03 14,5 3/16” Standard NO SKIVE 001C-04 04 15,5 1/4” Standard NO SKIVE 001C-05 05 17,8 5/16” Standard NO SKIVE 001C-06 06 20,4 3/8” Standard NO SKIVE 001C-08 08 23,4 1/2” Standard NO SKIVE 001C-10 10 26,8 5/8” Standard NO SKIVE 001C-12 12 31,0 3/4” Standard NO SKIVE 001C-16 16 38,8 1” Standard NO SKIVE 001C-20 20 48,0 1.1/4” Standard NO SKIVE 001C-24 24 55,2 1.1/2” Standard NO SKIVE 001C-32 32 68,4 2” Compressor; HyCelsius 1SN; TFDC011B; TFDH011B; 1SN Skive EN 853 1SN - SAE 100R1AT Inserto Pelatura Ghiera Insert Skive Ferrule Dash Ø Pressatura Swaging Ø Dash Est. Ext. Int. Int. Pollici Inch Lung. Ins. Insert Depth Standard SKIVE 0001-03 03 14,9 20 3/16” Standard SKIVE 0001-04 04 16,7 23 1/4” Standard SKIVE 0001-05 05 19,2 23 5/16” Standard SKIVE 0001-06 06 21,1 24 3/8” Standard SKIVE 0001-08 08 25,0 25 1/2” Standard SKIVE 0001-10 10 28,3 27 5/8” Standard SKIVE 0001-12 12 32,3 31 3/4” Standard SKIVE 0001-16 16 39,9 37 1” Standard SKIVE 0001-20 20 47,4 46 1.1/4” Standard SKIVE 0001-24 24 52,3 52 1.1/2” Standard SKIVE 0001-32 32 68,5 60 2” Kaizen 2SN; Hypress 2SN; HyFreeze 2SN; THD0021; THDM021; TFD0021; TFDM021; TFDL021N; 2SN R2AT EN 853 2SN -SAE 100 R2AT - ISO 1436 2SN Inserto Pelatura Ghiera Insert Skive Ferrule Dash Ø Pressatura Swaging Ø Dash Est. Ext. Int. Int. Pollici Inch Lung. Ins. Insert Depth Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 1/18
Transcript of IMM SWAGING CHART · IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019 Emessa da: Mauro Di...
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Hypress 1SN; HyFreeze 1SN; Railway; TFD0011; TFDL011N; TFDE0111SN R1AT
EN 853 1SN SAE 100 R1AT ISO 1436 1SN
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0303 14,53/16”
Standard NO SKIVE001C0404 15,51/4”
Standard NO SKIVE001C0505 17,85/16”
Standard NO SKIVE001C0606 20,43/8”
Standard NO SKIVE001C0808 23,41/2”
Standard NO SKIVE001C1010 26,85/8”
Standard NO SKIVE001C1212 31,03/4”
Standard NO SKIVE001C1616 38,81”
Standard NO SKIVE001C2020 48,01.1/4”
Standard NO SKIVE001C2424 55,21.1/2”
Standard NO SKIVE001C3232 68,42”
Compressor; HyCelsius 1SN; TFDC011B; TFDH011B; 1SN Skive
EN 853 1SN SAE 100R1AT
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard SKIVE00010303 14,9 203/16”
Standard SKIVE00010404 16,7 231/4”
Standard SKIVE00010505 19,2 235/16”
Standard SKIVE00010606 21,1 243/8”
Standard SKIVE00010808 25,0 251/2”
Standard SKIVE00011010 28,3 275/8”
Standard SKIVE00011212 32,3 313/4”
Standard SKIVE00011616 39,9 371”
Standard SKIVE00012020 47,4 461.1/4”
Standard SKIVE00012424 52,3 521.1/2”
Standard SKIVE00013232 68,5 602”
Kaizen 2SN; Hypress 2SN; HyFreeze 2SN; THD0021; THDM021; TFD0021;
TFDM021; TFDL021N;2SN R2AT
EN 853 2SN SAE 100 R2AT ISO 1436 2SN
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 1/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Kaizen 2SN; Hypress 2SN; HyFreeze 2SN; THD0021; THDM021; TFD0021;
TFDM021; TFDL021N;2SN R2AT
EN 853 2SN SAE 100 R2AT ISO 1436 2SN
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00220303 16,23/16”
Standard NO SKIVE00220404 17,51/4”
Standard NO SKIVE00220505 19,45/16”
Standard NO SKIVE00220606 20,93/8”
Standard NO SKIVE00220808 25,11/2”
Standard NO SKIVE00221010 28,55/8”
Standard NO SKIVE00221212 32,33/4”
Standard NO SKIVE00221616 40,81”
Standard NO SKIVE00222020 50,91.1/4”
Standard NO SKIVE00222424 58,01.1/2”
Standard NO SKIVE00223232 70,82”
HyClesius 2SN; TFDH021B2SN Skive
EN 853 2SN SAE 100 R2AT ISO 1436 2SN
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard SKIVE00020303 16,6 213/16”
Standard SKIVE00020404 17,8 221/4”
Standard SKIVE00020505 20,5 225/16”
Standard SKIVE00020606 22,1 243/8”
Standard SKIVE00020808 25,1 251/2”
Standard SKIVE00021010 28,5 275/8”
Standard SKIVE00021212 33,0 313/4”
Standard SKIVE00021616 40,3 371”
Standard SKIVE00022020 50,8 431.1/4”
Standard SKIVE00022424 57,2 451.1/2”
Standard SKIVE00023232 69,5 612”
Hypress 1SC; Hipac 1SC; Longlife 1SC; LongLift 1SC; LongLife Dual
1SC;TFE001K; THE001K;THE101K; THL101K; T2E101K1SC
EN 857 1SC ISO 11237 1SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0303 13,83/16”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 2/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Hypress 1SC; Hipac 1SC; Longlife 1SC; LongLift 1SC; LongLife Dual
1SC;TFE001K; THE001K;THE101K; THL101K; T2E101K1SC
EN 857 1SC ISO 11237 1SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,11/4”
Standard NO SKIVE001C0505 16,95/16”
Standard NO SKIVE001C0606 19,43/8”
Standard NO SKIVE001C0808 22,61/2”
Standard NO SKIVE001C1010 26,05/8”
Standard NO SKIVE001C1212 30,13/4”
Standard NO SKIVE001C1616 37,41”
Standard NO SKIVE001C2020 45,51.1/4”
Standard NO SKIVE001C2424 53,61.1/2”
Standard NO SKIVE001C3232 66,22”
Standard NO SKIVE001C4040 79,22.1/2”
Standard NO SKIVE001C4848 91,03”
Hypress 2SC; Hipac 2SC; Longlife 2SC ; HyOzone; LongLift 2SC; LongLife Dual
2SC; TFE002K; THE002K; THEM02K; THE102K; TFEM02KN; THL102K; 2SC
EN 857 2SC ISO 11237 2SC SAE 100R16
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0303 14,73/16”
Standard NO SKIVE001C0404 15,51/4”
Standard NO SKIVE001C0505 17,85/16”
Standard NO SKIVE001C0606 20,43/8”
Standard NO SKIVE001C0808 23,21/2”
Standard NO SKIVE001C1010 26,85/8”
Standard NO SKIVE001C1212 30,73/4”
Standard NO SKIVE001C1616 38,61”
Standard NO SKIVE001C2020 46,91.1/4”
Standard NO SKIVE001C2424 55,01.1/2”
Standard NO SKIVE001C3232 67,82”
Standard NO SKIVE001C4040 81,22.1/2”
Standard NO SKIVE001C4848 92,63”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 3/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Hypress Easy K 1SC; TFA201K Easy K 1SC
EN 857 1SC ISO 11237 1SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,11/4”
Standard NO SKIVE001C0505 16,95/16”
Standard NO SKIVE001C0606 19,43/8”
Standard NO SKIVE001C0808 22,61/2”
Standard NO SKIVE001C1010 26,05/8”
Standard NO SKIVE001C1212 30,13/4”
Standard NO SKIVE001C1616 37,41”
Hypress Easy K 2SC; TFA202K Easy K 2SC
EN 857 2SC ISO 11237 2SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,51/4”
Standard NO SKIVE001C0505 17,85/16”
Standard NO SKIVE001C0606 20,43/8”
Standard NO SKIVE001C0808 22,81/2”
Standard NO SKIVE001C1010 26,55/8”
Standard NO SKIVE001C1212 30,73/4”
Standard NO SKIVE001C1616 38,61”
TFS0017 R17
SAE 100 R17 (3000 PSI) ISO 11237 R17
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0303 13,53/16”
Standard NO SKIVE001C0404 15,11/4”
Standard NO SKIVE001C0505 16,95/16”
Standard NO SKIVE001C0606 19,43/8”
Standard NO SKIVE001C0808 22,81/2”
Standard NO SKIVE001C1010 26,85/8”
Standard NO SKIVE001C1212 30,73/4”
Standard NO SKIVE001C1616 39,21”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 4/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Marathon ; THE0M2K; THEMM2K 2MC
EN 857 2SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,51/4”
Standard NO SKIVE001C0505 17,85/16”
Standard NO SKIVE001C0606 20,43/8”
Standard NO SKIVE001C0808 23,21/2”
Standard NO SKIVE001C1010 26,85/8”
Standard NO SKIVE001C1212 30,73/4”
Standard NO SKIVE00221616 39,41”
Hipac 3SC; THE003K 3SK
3SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard SKIVE00020606 22,0 243/8”
Standard SKIVE00020808 26,2 251/2”
Standard SKIVE00021010 29,2 275/8”
Standard SKIVE00021212 34,1 313/4”
Standard SKIVE00021616 42,3 371”
Jet 1SN; JetPlus 1SN; TFN0011; TFB0011; THN0011; THB0011 JET / JET PLUS 1SN
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,51/4”
Standard NO SKIVE001C0505 17,85/16”
Standard NO SKIVE001C0606 20,43/8”
Standard NO SKIVE001C0808 23,41/2”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 5/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Jet 2SN; JetPlus 2SN; TFN0021; TFB0021; THN0021; THB0021 JET / JET PLUS 2SN
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00220404 17,51/4”
Standard NO SKIVE00220505 19,45/16”
Standard NO SKIVE00220606 20,93/8”
Standard NO SKIVE00220808 25,11/2”
Jet 1SC; JetPlus 1SC; TFN001K; TFB001K; THN001K; THB001K JET / JET PLUS 1SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,11/4”
Standard NO SKIVE001C0505 16,95/16”
Standard NO SKIVE001C0606 19,43/8”
Standard NO SKIVE001C0808 22,61/2”
Jet 2SC; JetPlus 2SC; TFN002K; TFB002K; THN002K; THB002K JET / JET PLUS 2SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0404 15,51/4”
Standard NO SKIVE001C0505 17,85/16”
Standard NO SKIVE001C0606 20,43/8”
Standard NO SKIVE001C0808 23,21/2”
TSW2280 SEWERJET 280
SewerJet 280 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0606 19,43/8”
Standard NO SKIVE001C0808 23,21/2”
Standard NO SKIVE001C1212 30,73/4”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 6/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TSW2280 SEWERJET 280
SewerJet 280 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C1616 38,61”
Standard NO SKIVE001C2020 46,91.1/4”
TFE0P10; TFE1P10; TFE0P15; TFE1P15 IMM Pilot
IMM Pilot
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0303 13,83/16”
Standard NO SKIVE001C0404 15,01/4”
Standard NO SKIVE001C0505 16,85/16”
Standard NO SKIVE001C0606 19,33/8”
Standard NO SKIVE001C0808 21,81/2”
TFE1PF2 PilotFlex 120
PilotFlex 120
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C0303 12,83/16”
Standard NO SKIVE001C03SW 10,8
Standard NO SKIVE001C0404 14,01/4”
Standard NO SKIVE001C04SW 14,3
HyJack; THE2J2K HYJACK
Hyjack
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Multispiral SKIVE002M0404 15,4 291/4”
Multispiral SKIVE002M0606 20,0 313/8”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 7/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Hytruck 200 bar; TTRK200 HYTRUCK 200
HyTruck 200
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C1212 30,13/4”
Standard NO SKIVE001C1616 38,61”
Hytruck 250 bar;TTRK250 HYTRUCK 250
HyTruck 250
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C1212 30,13/4”
Standard NO SKIVE001C1616 38,61”
Hytruck 350 bar;TTRK350 HYTRUCK 350
HyTruck 350
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C1212 30,73/4”
Standard NO SKIVE001C1616 38,61”
THEPS1KB; THEPS1KN Snow Storm
Snow Storm 1SC
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C1616 37,41”
Standard NO SKIVE001C2424 53,61.1/2”
Standard NO SKIVE001C3232 66,22”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 8/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
THE0L1K; Powerlift 1SC
EN 857 1SC EN 8120
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE001C1616 37,31”
Standard NO SKIVE001C2020 45,01.1/4”
Standard NO SKIVE001C2424 53,01.1/2”
Hypress R15; HyGreen R15;TFSM015; TFDG015;TFDR015 R15
ISO 3862 R15 SAE 100 R15 (6000 PSI)
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE00131010 29,8 47 155/8”
Interlock SKIVE004N1212 33,2 52 153/4”
Interlock SKIVE00131616 43,3 64 171”
Interlock SKIVE00132020 54,2 74 221.1/4”
Interlock SKIVE00132424 60,5 81 22,51.1/2”
Interlock SKIVE00133232 77,9 85 302”
Hypress R13; HyGreen R13;TFSM013; TFDG013; TFDR013 R13
EN 856 R13 SAE 100 R13 (5000 PSI) ISO 3862 R13
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Waterblast SKIVE00S40606 23,7 34 153/8”
Waterblast SKIVE00S40808 28,0 34 131/2”
Interlock SKIVE004N1212 33,2 52 153/4”
Interlock SKIVE00131616 43,3 64 171”
Interlock SKIVE00132020 54,2 74 221.1/4”
Interlock SKIVE00132424 60,5 81 22,51.1/2”
Interlock SKIVE00133232 77,9 85 302”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 9/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Hypress 4SH;HyGreen 4SH; TFDM4SH; TFD04SH; TFDG4SH; TFDR4SH 4SH
EN 856 4SH ISO 3862 4SH
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE004N1212 33,0 52 153/4”
Interlock SKIVE004N1616 41,2 64 171”
Interlock SKIVE004N2020 50,5 74 221.1/4”
Interlock SKIVE004N2424 56,8 81 22,51.1/2”
Interlock SKIVE004N3232 72,7 85 302”
Hypress 4SP; TFDM4SP; TFD04SP 4SP
EN 856 4SP ISO 3862 4SP
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard SKIVE00090404 18,5 221/4”
Standard SKIVE00090606 23,2 263/8”
Standard SKIVE00090808 26,5 281/2”
Standard SKIVE00091010 30,1 315/8”
Standard SKIVE00091212 33,8 343/4”
Multispiral NO SKIVEBMC212 38,6
Standard SKIVE00091616 42,3 481”
Standard NO SKIVEBMC116 46,0
Standard SKIVE00092020 51,2 541.1/4”
Standard NO SKIVEBMC220 57,3
Standard SKIVE00092424 60,3 621.1/2”
Standard SKIVE00093232 73,2 642”
Hypress R12; TFSM012 R12
EN 856 R12 SAE 100 R12 ISO 3862 R12
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard SKIVE00090606 23,2 263/8”
Standard SKIVE00090808 27,0 281/2”
Standard SKIVE00091010 30,6 315/8”
Standard NO SKIVEBMC11212 37,23/4”
Standard SKIVE000912 33,2 34
Standard SKIVE00091616 41,7 481”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 10/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
Hypress R12; TFSM012 R12
EN 856 R12 SAE 100 R12 ISO 3862 R12
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVEBMC11616 45,41”
Standard SKIVE00092020 50,1 541.1/4”
Standard SKIVE00092424 59,0 621.1/2”
Standard SKIVE004H3232 70,5 652”
TFS04JG Mega Jet
Mega Jet 4 spirals
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE004N1616 41,2 64 171”
Interlock SKIVE004N2020 50,5 74 221.1/4”
Interlock SKIVE004N2424 56,8 81 22,51.1/2”
Interlock SKIVE004N3232 72,7 85 302”
THS00JG Mega Jet
Mega Jet 6 spirals
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE00J61616 46,0 65 171”
Interlock SKIVE00132020 54,2 74 221.1/4”
Interlock SKIVE00132424 60,5 81 22,51.1/2”
Interlock SKIVE00133232 77,9 85 302”
BOP Firescreen; TBOP350 BOP 5000
BOP
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE00133232 77,9 85 302”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 11/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
THDB4SH BIO-FLEX
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE004N1212 33,0 52 153/4”
THEMMDR MEGADRILL
MEGADRILL
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Interlock SKIVE00134040 89,0 125 352.1/2”
Interlock SKIVE00134848 104,0 135 373”
TFW0070 HB 10k
Hyblast 10k 700 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Waterblast SKIVE00S41616 43,5 49 181”
TFW0085 HB 12k
Hyblast 12k 850 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Multispiral SKIVE00190404 18,2 301/4”
Waterblast SKIVE00S40606 22,6 34 153/8”
Waterblast SKIVE00S40808 26,8 34 131/2”
Waterblast SKIVE00S41212 35,0 42 153/4”
Waterblast SKIVE00Y61616 48,0 68 301”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 12/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TFW0110; TFW0100HB 15k
Hyblast 15k 1000 1100 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Multispiral SKIVE00190404 18,2 301/4”
Waterblast SKIVE00S40606 23,2 34 153/8”
Waterblast SKIVE00S40808 28,0 34 131/2”
Waterblast SKIVE00Y41212 37,8 56 253/4”
TFW0125; TFW0120HB 18k
Hyblast 18k 1200 1250 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Waterblast SKIVE00Y40606 27,5 50 223/8”
Waterblast SKIVE00Y40808 30,5 52 231/2”
TFW0145; TFW0135HB 20k
Hyblast 20k 1350 1450 bar
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Waterblast SKIVE00Y60606 30,0 50 223/8”
Waterblast SKIVE00Y60808 33,5 52 231/2”
Waterblast SKIVE00Y61212 41,0 56 253/4”
TFS0006; TFS1006;R6
SAE 100 R6
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00070303 13,03/16”
Standard NO SKIVE00070404 14,21/4”
Standard NO SKIVE00070505 16,85/16”
Standard NO SKIVE00070606 18,53/8”
Standard NO SKIVE00070808 22,61/2”
Standard NO SKIVE00071010 25,65/8”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 13/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TFS0006; TFS1006;R6
SAE 100 R6
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00071212 29,53/4”
Standard NO SKIVE00071616 37,01”
TFS0003R3
SAE 100R3 ISO 4079 R3
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00030303 14,63/16”
Standard NO SKIVE00030404 17,01/4”
Standard NO SKIVE00030505 18,45/16”
Standard NO SKIVE00030606 21,13/8”
Standard NO SKIVE00030808 25,71/2”
Standard NO SKIVE00031010 29,75/8”
Standard NO SKIVE00031212 33,23/4”
Standard NO SKIVE00031616 40,51”
Standard NO SKIVE00032020 46,21.1/4”
Standard NO SKIVE00032424 ―1.1/2”
Standard NO SKIVE00033232 ―2”
TFD02TE;2TE
EN 854 2TE
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00070404 14,51/4”
Standard NO SKIVE00070505 16,35/16”
Standard NO SKIVE00070606 18,53/8”
Standard NO SKIVE00070808 22,61/2”
Standard NO SKIVE00071010 24,95/8”
Standard NO SKIVE00071212 28,83/4”
Standard NO SKIVE00071616 37,01”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 14/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TFD03TE3TE
EN 854 3TE
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00030505 17,95/16”
Standard NO SKIVE00030606 20,03/8”
Standard NO SKIVE00030808 23,01/2”
Standard NO SKIVE00031010 26,55/8”
Standard NO SKIVE00031212 31,83/4”
Standard NO SKIVE00031616 40,91”
TFS0005R5
SAE 100 R5
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00030405 15,65/16”
Standard NO SKIVE00030506 18,13/8”
Standard NO SKIVE00030608 20,51/2”
Standard NO SKIVE00030810 24,55/8”
Standard NO SKIVE00031012 27,73/4”
Standard NO SKIVE00031216 31,61”
TFS0004R4
SAE 100 R4
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00031212 33,03/4”
Standard NO SKIVE00031616 41,01”
Standard NO SKIVE00032020 47,31.1/4”
Standard NO SKIVE00112424 52,41.1/2”
Standard NO SKIVE00113232 66,32”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 15/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TFS0007; TFS0NC7; TFS00M7: TFS00Y7; TFS00V7R7
EN 855 R7
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00070303 11,53/16”
Standard NO SKIVE00070404 13,71/4”
Standard NO SKIVE00070505 16,45/16”
Standard NO SKIVE00070606 18,23/8”
Standard NO SKIVE00070808 22,51/2”
Standard NO SKIVE00071010 25,65/8”
Standard NO SKIVE00071212 28,73/4”
TFS0008; TFS0NC8; TFS00M8; TFS00Y8; TFS00V8R8
EN 855 R8
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00080202 10,002
Standard NO SKIVE00080303 11,63/16”
Standard NO SKIVE00080404 13,91/4”
Standard NO SKIVE00080505 16,65/16”
Standard NO SKIVE00080606 18,83/8”
Standard NO SKIVE00080808 22,61/2”
Standard NO SKIVE00081010 26,25/8”
Standard NO SKIVE00081212 29,83/4”
Standard NO SKIVE00081616 37,81”
TFS00H1; TFS0H1M; TFS00V11 TRECCIA H1/V1
Termoplastico Acciaio 1 treccia
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00080303 12,13/16”
Standard NO SKIVE00080404 14,41/4”
Standard NO SKIVE00080505 16,45/16”
Standard NO SKIVE00080606 18,53/8”
Standard NO SKIVE00080808 21,81/2”
Standard NO SKIVE00081010 25,45/8”
Standard NO SKIVE00081212 29,13/4”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 16/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TFS00H1; TFS0H1M; TFS00V11 TRECCIA H1/V1
Termoplastico Acciaio 1 treccia
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00081616 37,41”
TFS00H2; TFS00V22 TRECCE H2/V2
Termoplastico Acciaio 2 trecce
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVE00220404 16,51/4”
Standard NO SKIVE00220606 19,73/8”
TFSNCHPVHP NC
Termoplastico rinf misto alte pressioni Non conduttivo
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Multispiral SKIVE00190404 17,0 301/4”
TF000T1PTFE
SAE 100 R14
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVEPTFE0303 10,33/16”
Standard NO SKIVEPTFE0404 12,01/4”
Standard NO SKIVEPTFE0505 14,75/16”
Standard NO SKIVEPTFE0606 16,03/8”
Standard NO SKIVEPTFE0808 18,91/2”
Standard NO SKIVEPTFE1212 26,23/4”
Standard NO SKIVEPTFE1616 33,21”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 17/18
Tabella dei diametri di pressatura consigliatiChart of recommended swaging diameters
IMM SWAGING CHART Revisione: Rev. R12.2 del 14/06/2019
Emessa da: Mauro Di Iorio
Approvata da: lorenzo panzone
TF00LTCPTFEC
Teflon corrugato
Inserto PelaturaGhieraInsert SkiveFerrule
Dash Ø PressaturaSwaging ØDash
Est.Ext.
Int.Int.
PolliciInch
Lung. Ins.Insert Depth
Standard NO SKIVEPTFE06C06 15,53/8”
Standard NO SKIVEPTFE08C08 19,11/2”
Standard NO SKIVEPTFE10C10 22,55/8”
Standard NO SKIVEPTFE12C12 26,53/4”
Standard NO SKIVEPTFE16C16 32,41”
Standard NO SKIVEPTFE20C20 45,11.1/4”
Standard NO SKIVEPTFE24C24 51,01.1/2”
Dimensioni: mm - Tolleranza media +0.00/-0.2 / Dimensions: mm - Average tolerance +0.00/-0.2 18/18
