Modulo WiFiWiFi module · E-MAIL SETUP Figure 13 E-mail page Figure 12 E-mail page – enabled / 9...
Transcript of Modulo WiFiWiFi module · E-MAIL SETUP Figure 13 E-mail page Figure 12 E-mail page – enabled / 9...
Electronic control systems designers
Modulo WiFiWiFi module
/ 1
Wireless connection
Out of box operations
Data station con�guration
E-mail setup
Status page contents
Data logger setup
Information summary
_02
_03
_04
_08
_11
_12
_15
INDEX
@ROUTER
AP
WiFi module
/ 2
Questo particolare modello della serie BR1-28 contiene al suo interno un modulo per la connessione ad una rete WiFi, mediante la quale può comunicare sia con dispositivi mobili (smartphone) che con PC.Tramite un web browser è possibile controllare lo stato generale del regolatore, ovvero: valore degli ingressi, del setpoint corrente e degli allarmi.
Grazie alla funzione di memorizzazione automatica, questi dati vengono salvati nella memoria interna per rimanere consultabili, semplicemente e velocemente con il vostro Smartphone.
In�ne, se tramite un router WiFi è disponibile una connessione ad Internet, in caso di allarme verrà generata una e-mail che noti�cherà: ora e tipo di allarme, durata e impianto ove è avvenuto. Tutto questo aggiunge alle già notevoli prestazioni dei regolatori della serie BR1-28 una potentissima funzione di diagnostica e consente un incredibile passo in avanti verso la sicurezza totale.
Modalità ACCESS POINT Connessione con smartphone
Modalità INTERNET Connessione alla rete tramite router
Modalità WLAN Connessione con pc tramite Access Point
WIRELESS CONNECTION
This wireless module, which may be �tted in several LAE controllers, allows the connection to a WiFi network, through which it can communicate both with smartphones and a PC’s. Through a web browser it's possible to check the general state of a controller, that is: values of inputs, current setpoint and alarms.
Thanks to the automatic storage function, all those data are saved in the internal memory and may be consulted at any time, simply and quickly, by means of your smartphone.
In addition, if through a WiFi router a connection to Internet is available, in case of an alarm, an e-mail message will be generated, to notify: time and type of alarm, duration and plant where it has taken place.
All this adds a very powerful diagnostics function to the already outstanding performances of the LAE controllers and it allows an incredible leap forward to total safety.
ACCESS POINT mode Connection to a smartphone
INTERNET mode Connection to a network through a Router
WLAN mode Connection to a PC through an Access Point
Figure 2Status page
Figure 3Name of WiFi Access Point
Figure 1Connected to access point
WiFi module
/ 3
Alla prima accensione BR1-28 appare come un access point. Per con�gurarlo procedere al collegamento con uno smartphone come segue:
1. Accendere il controllore
2. Disabilitare la rete 3G nello smartphone e attivare il WiFi
3. Cercare tra le reti WiFi disponibili l’SSID riportato nell’etichetta sotto il codicea barre (Figure A) e connettersi (Figure B)
4. Con un browser web digitare l’indirizzo “wi�.net” oppure “192.168.1.1”
5. Apparirà la status page (Figure C)
At the �rst power-up of the controller where the WiFi module is in, this shows up as an Access Point.To set it up, proceed to connecting it to a smartphone, following the procedure hereinafter:
1. Power the controller
2. Disable the 3G network of the smartphone and activatethe WiFi connection
3. Search the SSID appearing on the label under the bar code(Figure 3) among the available WiFi networks, then getconnected (Figure 1)
4. With a web browser digit the "wi�.net" address or "192.168.1.1"
5. Now, a status page will appear (Figure 2)
OUT OF BOX OPERATIONS
Figure 5Status page – network
Figure 4Status page - menu
/ 4
WiFi module
CONFIGURAZIONE
A questo punto, la prima operazione da eseguire sarà di con�gurare e personalizzare la "stazione" di trasmissione dati: tramite un testo descrittivo, si dovrà rendere chiaramente riconoscibile l'unità alla quale si è collegati o che invierà i messaggi di allarme tramite e-mail.
1. Dal menù a tendina (Figure D) selezionare la voce Settings > Network
2. Name/Description Nel campo "Name/Description" digitare il testo, con un limite di 33 caratteri alfanumerici (no spazio), che poi apparirà su tutte le intestazioni dei documenti/pagine relative alla stazione; es.: Frigo-surgelati-01 (Figure E)
DATA STATION CONFIGURATION
Now, the �rst operation to be performed will be to con�gure and customise the data transmission "station", through a descriptive text; you will have to make the unit to which you are connected or which will send e-mail alarms clearly identi�able.
1. In the pull-down menu (Figure 4) select the optionSetting > Network
2. In the Name/Description �eld, digit a text, with the limit of33 alpha-numeric characters (no space), which will thenappear in all the document/page headers relating to thestation; ex. Freezer-01 (Figure 5)
DATA STATION CONFIGURATION
Figure 7Status page – Station mode data
Figure 6Station mode selection
/ 5
WiFi module
3. Device modeScegliere tra le due opzioni “Station” e “Access Point”.
3a. Modalità Station
Per usufruire della piena funzionalità del modulo, sarà indispensabile avere una rete WLAN a cui collegarsi. Selezionare la modalità "Station" (Figure F).
Compilare i campi successivi con i dati relativi al vostroAccess Point: SSID, password, etc... (Figure G).
3. Device modeThis selection will allow you to obtain di�erent levels of performance from your WiFi module. Choose between the two options "Access point" and "Station".
4a. Station Mode
In order to use the whole functionality of the module,it will be necessary to have a WLAN network to get connected to. Thus, pass from "Access Point" to"Station" mode (Figure 6)
4a.1. Type in the data relating to your Access Point, i.e.:SSID, password, etc... (Figure 7)
4a.2. With your smartphone, now connect to the networkAccess Point and through it to the new station.To make this easier, you may use free APP's allowing a smart mDNS function, for ex.: Zentri discovery for Android
DATA STATION CONFIGURATION
Figure 9Status page – Access Point mode data
Figure 8Mode selection – Access Point
WiFi module
/ 6
3b. Modalità Access Point (Figure H)
È la modalità di default, necessaria qualora non vi fossealcuna rete WLAN a cui collegarsi. In questo modo il dispositivo risulterà successivamente accessibile dal vostro smartphone con le stesse modalità usate per la con�gurazione.
Ora il modulo risulterà raggiungibile solo localmente e da un solo smartphone alla volta, non potrà inviare messaggi e neppure aggiornare automaticamente data e ora.
Malgrado il fatto che il modulo risulti ora accessibile soloentro un raggio abbastanza ristretto, sarà comunque opportuno proteggerlo da accessi non autorizzati compilando opportunamente i campi “Security type” e “Password” (Figure I).
4b. Access Point Mode (Figure 8)
This is the default mode, necessary whenever there will be no WLAN network to which you can connect. In this way, the device will then turn out to be accessible from your smartphone with the same credentials of the con�guration (see point 2.)
In the Access Point mode, your WiFi module will turn out to be accessible locally only and from a single smartphone at a time; it will neither be able to send messages or update date and time automatically.
Although the module now turns out to only be accessible within a relatively narrow range, it will however be opportune to protect it against non authorised attempts of access; thus, the �elds "Security type" and "Password" (Figure 9) will have to be �lled in duly.
DATA STATION CONFIGURATION
Figure 10Status page – setting con�rmation
WiFi module
/ 7
4. Terminate le operazioni precedenti, premere il tasto“Apply” a fondo pagina per renderle subito operative(Figure L).
Ripristino
Qualora per qualche motivo (operazioni errate o cambio di rete) fosse necessario ripristinare la con�gurazione di fabbrica, rifarsi alle istruzioni del BR1-28 per le operazioni da eseguire.
5. After performing the operations detailed before, press key"Apply" at the page bottom in order to make them operational immediately (Figure 10)
Reload
Whenever, for whatever reason (wrong operations or network change), it turned out to be necessary to reload the factory setting, refer to the instructions of the display to be associated to the controller in which the WiFi module resides.
Figure 11E-mail page
/ 8
WiFi module
The WiFi module is able to send an e-mail message at the occurance and end of an alarm condition and/or, on a regular basis, the log �le stored.
If you have to serve more di�erent plants, we suggest to create a mail account per each of them and assign a mnemonic to the device, in order to be able to identify sender quickly.For reference, see Figure 11 here at the side.
Con�gure the e-mail function as explained in the following pages.
E-MAIL SETUP
E-MAIL SETUP
Figure 13E-mail page
Figure 12E-mail page – enabled
/ 9
WiFi module
All’attivazione un nuovo allarme il modulo invierà una e-mail di avviso (Figure O). Allo stesso modo, quando l’allarme termina arriverà una e-mail di �ne allarme(Figure P).
Example
1. In the pull-down menu, select the option Settings > Email
2. Enable e-mails (Figure 12)
3. Fill in the �elds with correct data (Figure 13):in "Host name", digit the sender's host that you are goingto use:• For gmail: smtp.gmail.com• For yahoo: smtp.mail.yahoo.com
4. In "Host port" digit the port number to be used:• For gmail and yahoo: 465
5. In "Email address" digit the sender's address(ex. [email protected])
6. In "Password" digit the sender's account password
7. In "Email receiver" digit the receiver's e-mail address(ex. [email protected])
8. In "Email object" digit the mail object(ex. Freezer-01 Alarm report)
9. In "Email text" digit the mail text, which will complete thetext generated by the module automatically
10. Press "Apply" to save the new setup
Figure 15E-mail example – alarm end
E-MAIL SETUP
Figure 14E-mail example – alarm start
/ 10
WiFi module
Contenuti della status page
Nella status page verranno visualizzati il riepilogo dei parametri e lo stato degli allarmi.
Se non ci sono allarmi la spia è di colore verde (Figure Q)
Gli allarmi in corso vengono visualizzati con la spia di colore rosso e con una breve descrizione (Figure R)
When a new alarm occurs, the module will send an e-mail notice (Figure 14). In the same manner, when an alarm in a controller is over, an alarm end e-mail will be sent (Figure 15)
Example
Figure 17Status page - Alarm
Figure 16Status page - No alarm
/ 11
WiFi module
Per regolare il formato della data, il fuso orario e la scala della temperatura, accedere alla sezione “Data Logger” come segue:
1. Dal menù a tendina selezionare la voce Settings >Data logger. Il campionamento di temperature e allarmi avviene ogni 5 minuti.
2. Select the display scale for temperatures (Figure S): a) 0.1°C = Celsius degrees with 1 tenth resolution b) 1°C = Celsius degrees resolution c) °F = Fahrenheit degrees
3. Enter local time hour an minute di�erence to GMT
4. Press “Apply” to save the con�guration
SETUP THE DATA LOGGERStatus page contents
In the status page, a summary of the parameters and alarm status will appear.
If there are no alarms in progress, the alarm indicator is colour green, otherwise the alarms in progress are displayed with the red indicator and a short description (Figure 17)
As a plus, we o�er the option to send a log mail instantly by pressing button "Send email" at the bottom of the home window.
Figure 19Data logger page
Figure 18Data logger page
/ 12
WiFi module
Per visualizzare l’archivio dei campionamenti accedere dalla sezione “Log” come segue:
1. Per visualizzare l’archivio dati, dal menù a tendina selezionare la voce “Log” (Figure T):
In alto compare il nome assegnato al dispositivo.
I dati sono disposti in ordine cronologico dal più recente (in alto) ai precedenti (in basso).
Nelle prime due colonne si trovano data e ora del campionamento, nel caso in cui il modulo sia online in modalità Station.Diversamente, se in modalità Access point, quindi privo di connessione ad una rete internet, data e ora verranno sostituite da un numero progressivo.
Nella colonna AIR viene visualizzata la temperaturaNella colonna EVP viene visualizzata la temperaturaNella colonna T3 viene visualizzata la temperaturaNella colonna ALARMS vengono riportati i messaggi di inizio/termine degli allarmi
Un’interruzione di alimentazione viene segnalata con una sequenza di “=”.
Data logging is an important function for the diagnostics of the controlled system. The WiFi module, in addition to data logging, may also be programmed to send a mail at regular intervals, with the data formatted in such a manner as to be analysed with a spreadsheet or simply saved on a PC. The WiFi module uses the GMT time as internal clock, read from Internet. It shall therefore be necessary to correct the clock to obtain the local time. To adjust the date, time zone and temperature scale, go to "Data Logger" and follow the instructions here below:
Log function con�guration
1. In the pull-down menu, select option Setting > Data logger.
2. Select the temperature readout and display unit (Figure 19): a) 0.1°C = degrees Celsius with 0.1° resolution b) 1°C = 1°C resolution c) °F = degrees Fahrenheit
3. Type in the di�erence in hours and minutes of the local timein comparison to GMT
4. Press "Apply" to save the new con�guration
The temperature and alarm sampling rate is 5 minutes.
DATA LOGGER SETUP
Figure 18Data logger page
/ 13
WiFi module
Mail con�guration
5. If you wish to receive the logged data in a mail at regularintervals and automatically, select the frequency(1, 2 or 3 days).
6. ...and the time in HH and MM.
7. Fill in the mail object with a suitable description.
8. If you wish that in conjunction with a new alarm mail, thelog of the latest 24 hours is sent too, select "Enabled" in the�eld "Send E-mail log �le on Alarm".
DATA LOGGER SETUP
Figura 21
Figure 20
/ 14
WiFi module
To display the sampling data archive, get in "Log" bearing in mind the notes here below:
• On top the name assigned to the device appears
• The data are arranged in chronological order, from the most recent (top) to the previous ones (page bottom)
• If the module is online in Station mode, in the �rst two columns, date and time of sampling appear (Figure 20).Di�erently, if the module is working in Access Point mode, so no connection to Internet, date and time will be replaced by a progressive number (Figure 21).
• A series of columns will appear displaying temperatures and alarms, see image at the side
• A power supply interruption will be signalled by a sequence of "="
DATA LOGGER SETUP
Figure 22About page
/ 15
WiFi module
The "About" page includes an information summary relevant to the device settings: MAC ADDRESS, DHCP status, IP settings, if any, and Software release.
1. To get access to this section, in the pull-down menu selectoption "About" (Figure 22)
INFORMATION SUMMARY
Electronic control systems designers