DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2...

8
AiDRINK ® REV. 1.0 MADE IN ITALY AiDRINK Installation, User and Maintenance Manual DRINKING WATER TREATMENT UNIT Warning: This unit requires a regular maintenance operated only by a Qualified Technician to ensure the requirements of potability of the treated drinking wa- ter and the maintenance of the improvements as stated by the manufacturer.

Transcript of DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2...

Page 1: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

AiDRINK®

REV. 1.0

MADE IN ITALY

DISINTA COMPONENTIPER PROTOTIPAZIONE

28-09-11

POS NOME QTA COLORE

1 ANELLO-LED-V2 1 TRASPARENTE

2 GRIGLIETTA-V2 1 TRASPARENTE

3 MUSO-V2 1 NEUTRO

4 PIEDE-V2 1 NEUTRO

5 SCHIENA-V2 1 NEUTRO

6 STAFFA-V2 1 NEUTRO

7 TETTO-V2 1 NEUTRO

8 VASCHETTA-V2 1 NEUTRO

1

2

3

4

5

6

7

8

AiDRINK

Installation, User and Maintenance Manual

DRINKING WATER TREATMENT UNIT

Warning: This unit requires a regular maintenance operated only by a Qualified Technician to ensure the requirements of potability of the treated drinking wa-ter and the maintenance of the improvements as stated by the manufacturer.

Page 2: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

2 | ENGLISH ENGLISH | 2 ENGLISH | 3

Dear Customer, we thank you for buying our AiDRINK !

The microfiltration unit AiDRINK• Reduce the chlorine till 95%• It’s cheap• It gives you clean, pure and of good

quality water in order to ameliorate the taste of potable water.

• It consists in one carbon filter that is able to reduce chlorine, bad taste and smell.

• The Precoat microfiltration system removes impurities and particles big as or superior of 0,5 micron (Micro-filtration).

• Reduces contaminant agents that might be present like asbestos and some microorganisms like Crypto-sporidium and Giarda.

• It doesn’t remove scale or fluorides.• It is easy, fast and safety to substitute

the cartridge according the hygienic and health provisions. The internal part of the cartridge can’t be con-taminated from the exterior.

• It reduces the CO2 emissions (lower use of plastic bottles).

• It controls through an electronic sys-tem the life of the filter.

• It signals 30 days before the expiry date of the filter.

• Maximum working capacity: 1.9 Lpm• Maximum working pressure: 1.5 –

4.0 bar• Miximum ambient temperature: 2-

38 °C• NSF certification according NSF/

ANSI standard 42 & 53.

TECHNICAL DATA

POWER SUPPLY VOLTAGE12V DC

(External AC Power Adapter 110-240V/12V

50-60Hz included)

ROOM WORK TEMPERATURE 2-38 °C / 35.6-89.6 °F

MINIMUM INLET WATER TEMPERATURE 5 °C / 41.0 °F

MAXIMUM INLET WATER TEMPERATURE 25 °C / 77.00 °F

WATER SYSTEM WORKING PRESSURE 150-400 kPa (1.5-4 bar)

NET WEIGHT 1.5 Kg

GROSS WEIGHT 1.7 Kg

DIMENSIONS LxWxH 160x100x420 mm

PACKAGE DIMENSIONS LxWxH 115x310x445 mm

ACCESSORIES SUPPLIED Connection Kit, AC Adapter 110-240V/12V

DISPENSE AREA HEIGHT 26 cm

MAXIMUM WORKING CAPACITY 1.9 Litre per minutes

POWER CONSUMPTION - STAND BY 0.58 W

POWER CONSUMPTION - DISPENSING 11.3 W

Std. No. 42 - Aesthetic e�ectsChemical Reduction

Taste & OdorChlorine Taste & Odor

Mechanical FiltrationParticulate Class I

Std. No. 53 - Health e�ectsMechanical Filtration

CystAsbestos

System Tested and Certified by NSF International against NSF/ANSI Standard 42 and 53 for the reduction of:

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF/ANSI*This system has been tested according to NSF/ANSI 42 and 53 for thereduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced toa concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.

Substance Influent Challenge Concentration

Max. Permissable Product Water Concentration

Reduction Requirements

Minimum Reduction

Average Reduction

Standard 42 - Aesthetic E�ects

Chlorine 2.0 mg/L ± 10% ≥ 50% 95.7%

Particulate, Class I particles 0.5 to <1 µm

at least 10,000 particles/mL ≥ 85% 98%

Standard 53 - Health E�ects

Asbestos 10 7 to 10 8 fibers/L > 10 micrometers in length 99% 99.87% 99.87%

Cyst Minimum 50,000/L 99.95% 99.99% 99.99%

;5.0 ± 5.7 = Hp ;gisp 06 = erusserp ;mpg 5.0 = etar wofl gnisu detseT *temp. = 20° ± 2.5°C

† NTU = Nephelometric Turbidity Units

Performance and certification of Everpure filter on the efficacy to reduce chlorine, particles with dimensions between 0.5

and 1 μm, asbestos fibers and of Giarda, Entamoeba and

Cryptosporidium bacteria.

Page 3: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

2 | ENGLISH ENGLISH | 2 ENGLISH | 3

2. PACKAGING CONTENTPackaging contains the following:

• The AiDRINK dispenser• External AC Adapter 110-240V/12V• This manual• About 2mt of 6mm pipe• One 6x3/8 fitting

3. INSTALLATIONThe installation o fan AiDRINK has sto be done by a qualified technician.

WARNING: Asset declines any responsibil-ity in case of an installation made by non qualified personnel.

The installation and maintenance opera-tions has to be done preferable with health safety of hands and tools.

The placed used for this action has to re-spect the following conditions:

• Room temperature: +2 ÷ 38 ° C (35,6 ÷ 100,4 ° F)

• Maximum humidity: 80%

The dispenser must not be used in open spaces and/or exposed to atmospheric agents, under the sun or in room with steam, smoke or corrosive and/or abrasive dust, with fire or explosion risk, and any-way where it is prescribed to use products that may cause explosion.

FILTER LIFEThe Everpure filter has a filtration capacity of 2800 liters and it can’t be used over this limit.The filter replacement has to be done only by a qualified technician that needs to hold a chip card necessary to unlock the dispenser.The flow rate do not have to be more than 1.9 lpm.

Activate the cartridge at the first installa-tion and at every following replacement.WARNING: if the dispenser isn’t used for a period of more than 7 days (summer clou-sure or holidays) it is necessary to replace the filter and to make a sanification using the proper KIT P-SANIKIT (not included-with AiDRINK)

1. CLEANING INSTRUCTIONSFor a proper functioning of AiDRINK please follow carefully the instructions.

Do not merge the AiDRINK in water and do not wash it in a dishwasher, but only using a damp cloth.

It is preferable to use a gentle soap instead of an abrasive one. To descale the nozzle you can use a normal domestic descaling product with citric acid.

Never touch with your hands the nozzle, if not using monouse gloves.

Page 4: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

4 | ENGLISH ENGLISH | 4 ENGLISH | 5

On the back of the dispenser are shown:

1. Chip card slot2. Water inlet3. Power supply inlet

During installation the new pipes and fit-tings given for the connection to the wa-ter main have to replace the old ones and those old can’t be reused.

An interception valve is required on the point of use (not included with AiDRINK).

For a safe and correct functioning of the water dispenser, the main inlet water has to respect the following conditions:

• No over pressure• Maximum pressure like 150-400 kPa

(1.5 – 4 bar)

In case the pressure of the main water will be over 400 kPa (4 bar), it will be necessary to install a pressure reducer before the in-terception valve with a setting pressure of 300 kPa (3 bar).

To connect the dispenser to the water main it must be used, in an exclusively way, pipes and fitting given with the dis-penser and certified for food use.

Any optional accessory, like filter or prefil-ter, to install before the interception valve on the inlet main water, have to be certi-fied for food use.

For a proper installation to the water main please follow these procedures:1. Screw on the interception valve (not

included) the 6x3/8” male fitting to connect the pipe for water inlet sup-plied with the dispenser;

2. Insert the 6mm pipe given with the 6x3/8” fitting;

3. Place a proper tank/vessel at the end of the pipe and open the interception valve in order to spurge and clean the pipe and the possible external pre-fil-ter (if present) letting get out at least 2 liters of water;

4. After this you can close again the in-terception valve;

5. Now you can connect the pipe at the inlet on the back of the AiDRINK;

6. Open the interception valve in order to check that there aren’t any leakage from the fittings previously installed;

7. Remove the drip tray and the front cover; remove also the little oval plate located at the base of the filter, right under the drip tray.

8. Insert in the rear hole (located side by side the water pipe connection) the external 12V Power Supply cable and insert the plug into the socket located under the electronic main board.

9. Connect the External Power Supply. 10. Refit the oval plate, the front cover

and the drip tray.11. Wait that the AiDRINK terminates the

initial phase of electronic autodiag-nostic (during this phase the lights on the keyboard are lighting alternatively of blue and red for about 5 seconds). During this initial phase it is possible to adjust the value of Energy Saving of AiDRINK (see p. 6 – chapter 4 ENERGY SAVING).

12. Now the AiDRINK is ready to be used.

Page 5: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

4 | ENGLISH ENGLISH | 4 ENGLISH | 5

3. ICONS AND USEIn order to dispense water it is necessary to place the fleshy part of the fingertip on the Dispensing Key : to terminate dis-pensing remove the finger from the key.

DISPENSING ICONIt is enlightened when the AiDRINK dis-penses water.

PRE-ALARM FOR EXHAUSTING FILTERA red light is lightning to indicate that re-main 30 days till the exhausting of the fil-ter.SUGGESTION: please contact the technical assistance in order to replace the filter.

PRE-ALARM FOR EXHAUSTING FILTERA red light is lighting and it signals that the filter is almost exhausted: about 500 liters remain available before the dispenser will stop functioning.

FILTER LIFE STATUS

LED INDICATING REMAINING MONTHSThe switching-on of every single LED indi-cates about two month of filter life remain-ing.

LED INDICATING REMAINING LITERSThe switching-on of every single LED in-dicates about 500 liters remaining for the filter.

AiDRINK

Dispensing Key

Dispensing Icon

Time for expiring filter alarm

Liters for expiring filter alarm

FILTER LIFE STATUS

Leds indicating remaining months

Leds indicating remaining liters

Page 6: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

6 | ENGLISH ENGLISH | 6 ENGLISH | 7

3. FILTER REPLACEMENTThe replacement of the filter has to be done only by a qualified technician that must act following carefully the instruc-tion contained in this manual.

The PRODUCER is not responsible if the instructions for installation, use and main-tenance, explained in this manual, are not followed by the person who install the dis-penser or its user.

During warranty period, every unauthor-ized, or made by a unqualified person, in-tervention on the dispenser, will make this to lapse automatically.

Before to replace the filter it is recommend-ed to make a sanification of the dispenser by the proper sanification kit P-SANIKIT + JT CARTRIDGE (optional not supplied with the dispenser); this procedure must be done only by a qualified technician, unless the warranty, on the product, will lapse au-tomatically.

For a normal use of the dispenser, it is com-pulsory to replace the filter at least once per year or every six months, depending on the filter.

Once the filter has been in contact with water, needs to be replaced if the dispens-er isn’t used for a period no longer than 12 month or according to technical specifica-tions from the producer of this filter.

Together with the sanification kit, it is sup-plied an electronic chip card that will be needed by the qualified Asset technician - and only to him - in order to reset the dis-penser when, one of the previously men-

tioned conditions to replace the filter, will occur. The dispenser will still be blocked if this card is not inserted or it is inserted in a wrong way.

4. ENERGY SAVINGSIt is possible to adjust the lighting of the side LED at three different levels of lighting in order to optimize the energy saving.

Level 1: Leds always on (default)Level 2: Leds lighting in at randomLevel 3: Leds always off

In order to modify the desired energy sav-ing level, you need to disconnect the pow-er supply and connect this again, push immediately the dispensing key in order to change the energy saving level that will be indicated by the lighting of LED for few seconds on both LEDs side lines.

1 led on: Level 12 leds on: Level 23 leds on: level 3

The new energy saving mode will be on af-ter about two minutes of inactivity of the dispenser.

WARNING: if the dispenser is in energy saving mode, at the first touch of the dispensing key, it comes back to base function and it is necessary to press again the dispensing key in order to dis-pense water.

Page 7: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

6 | ENGLISH ENGLISH | 6 ENGLISH | 7

3

Wear the gloves provided with the kit and close the water

interception tap.

Press the room temperature key for a moment to decrease the

internal pressure. Unplug the rear power supply main connector.

Turn the coupling head of the cartridge of one-half

turn and remove it by pulling down.

Insert the smart card - supplied with the new �lter - in the proper

�ssure.

Turn the coupling head of the cartridge of one-half

turn and remove it by pulling down.

Insert the new Filter pushing it up and

screw it again of one-haft turn.

Open the water interception tap and dispense at least 1 litre of water in order to eliminate any

residue of sanitizing liquid.

Dispense 1 litre of water. Close the water interception tap and press the room temperature

key and keep it pressed until the dispenser doesn’t dispense water.

Add the Anolyte to the empty�ushing cartridge through the hole in the top and �ll to the

brim with drinking water.

Replace the central plug assembly. Insert then the JT Cartridge,

pushing it up and screw it again of one-haft turn.

Reconnect the rear power supply plug and open the water

interception tap. Dispense 2 glasses of water.

Unplug the rear power supply main connector.

Wait 15 minutes and reconnect the power supply.

Grasp the tip of the outlet tower and pull out gently.

B - SANITIZING USING THE JT CARTRIDGE

A - EXAUSTED FILTER REPLACEMENT

C - NEW FILTER INSTALLATION

2

8

7

6

5

5

4

Anolyte

2

SANITIZINGJT CARTRIDGE

SANITIZINGJT CARTRIDGE

EXA

UST

FIL

TER

NEW

FIL

TER 7

6

SANITIZINGJT CARTRIDGE

SANITIZINGJT CARTRIDGE

65

SANITIZINGJT CARTRIDGE

4

1

SAN

ITIZ

ING

JT C

AR

TRID

GE

SAN

ITIZ

ING

JT C

AR

TRID

GE

1

2

3

8

4

1

9

15

3

Page 8: DRINKING WATER TREATMENT UNIT 2 GRIGLIETTA-V2 1 ......1 ANELLO-LED-V2 1 TRASPARENTE 2 GRIGLIETTA-V2 1 TRASPARENTE 3 MUSO-V2 1 NEUTRO 4 PIEDE-V2 1 NEUTRO ... removes impurities and

DRINKING WATER TREATMENT UNIT.AiDRINK must be used only with pota-ble water that respects the applicable rules related to the quality of water for a human consumption. It is recommend-ed to use the Everpure filter with water harder more than 19°F.

Do not leave the AiDRINK directly ex-posed to the sun.Keep AiDRINK far from heating elements for example hovens, coffee machines etc. Place AiDRINK in a cool and shady place.

During the course of normal use of AiD-RINK, it is possible to see the appearing of scale on the nozzle. This is due to the fact that the nozzle is continuously in contact with non filtered water that contains carbonates (scale).

It is recommended to clean and descale the nozzle, unscrewing and merging it in a normal descaling liquid for home with citric acid.

In case of non use of the AiDRINK for a period of at least 7 days (ex. Summer holidays) it is recommended to remove the EVERPURE filter and to insert a new filter after the sanification of the AiD-RINK.For a good performance of the filter it is better to filter mainly cold main water.

Particular casesAiDRINK is produced and designed in order to be used only with main water treated by municipal companies (note: this water is constantly checked and it is potable at law requirement) o with water that comes from a private source which potability has been certificed. In case communication to boil the water have been received, it is needed to boil also the water dispensed from AiDRINK.

When the regulation to boil the water are no longer valid, AiDRINK must be completely sanitized and a new filter have to be used.

It is recommended anyway to boil the main water used for consumption of some catego-ries of persons (such as person with a defi-ciency in the immune system or newborn); the same advice is applicable at microfiltrat-ed water from AiDRINK.

Independently from the water used, it is rec-ommended to use tools in stainless steel or kettle with heating element protect.

Natural tracesAs any natural product, the consistency of the AiDRINK filter is subjected to natural changes.Transport may cause a little erasure of little carbon particles, that can be seen in the wa-ter with little black pieces.

This particles do not have any dangerous ef-fect on human health. If drunk, they are elimi-nated normally from our organism without any effect.

DisposalAiDRINK has a normal duration of five years. At the termination of normal duration, must be remembered that these appliances have to be disposed according to applicable rules and norms.

Warranty This product is covered by a warranty time of 24 months from the date of purchasing.

ResponsibilityAsset is not responsible for the non applica-tion, from the user, of the instruction use here indicated.

IMPORTANT NOTES

AiDRINK is Made in Italy by ASSET S.r.l.

Loc. Isola del Pero, 16 - 17041 - ALTARE (SV) - ITALY - Tel: +39 019 58 48 30Fax: +39 019 51 42 186 - e-mail: [email protected] - www.assetitalia.it

ASSET declines all liability for any damage to people or property caused by incorrect use of this product.Subject to change without prior notice.