ACUIX ES 800-01949 Full Guide Camara Domo

5/19/2018 ACUIX ES 800-01949 Full Guide Camara Domo

1/86

Document 800-01949 Rev D 05/09

Installation and

Configuration Guide

ACUIXES

PTZ Analog Dome


2/86

Revisions

Issue Date Revisions

A 07/08 New document for pre-production release.

B 09/08 Updated and corrected with information from beta for product release

C 10/08 Corrections (1) Fig 2-11 screw callout description (2) NA Manufacturer's Declarationof Conformance (3) Tables 2-2 and 2-3 (NTSC and PAL default DIP switch settings)deleted and replaced with new Table 2-2. (4) Table 2-1 NTSC and PAL defaultdescription changed and note added to clarify that camera model dependent

D 05/09 Addition of (1) Pelco P_AD and Pelco D_AD protocols (appendix A); (2) update toprivacy zone OSD menus and menu tree (pages 52 and 65).

File created: Apr 22, 2009


3/86

Document 800-01949 Rev D 3

05/09

Explanation of Symbols

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits for a Class B digitaldevice. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instruction manual, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the interference. For example, try orienting orrelocating the receiving antenna, increasing the separation between the equipment and receiver, or connecting theequipment to an outlet on a different circuit.

WARNING! The exclamation point in a red octagon is a WARNING. Failure to takeor avoid a specific action could result in physical harm to a personor irreparable damage to equipment.

Caution The lightning flash with arrowhead symbol within an equilateral trianglealerts the user to the presence of uninsulated dangerous voltage within theenclosure of the product that may be of sufficient magnitude toconstitute a risk of electric shock to the person.

Caution The exclamation point in a yellow equilateral triangle is a Caution. Failureto take or avoid a specified action could result in loss of data or damageto equipmentand may contain important operating and maintenanceservicing information.


4/86

4

Canadian Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.

Manufacturers Declaration of Conformance

North AmericaThe equipment supplied with this guide conforms to UL60065 and CAN/CSA C22.2 No. 60065-03.

EuropeThe manufacturer declares that the equipment supplied with this guide is compliant with the essential protection

requirements of the EMC directive 2004/108/EC and the Low Voltage Directive LVD 2006/95/EC, conforming to therequirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipmentsafety.

Changes or modifications not expressly approved by the party responsible for compliancecould void the users authority to operate the equipment.

Users of the product are responsible for checking and complying with all federal, state

and local laws and statutes concerning the monitoring and recording of video and audiosignals. Honeywell Video Systems shall not be held responsible for the use of this productin violation of current laws and statutes.


5/86


05/09

Warnings and Cautions

Read the following cautions and warnings prior to installation and use of this product.

Important Safety Instructions

BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOW ALL INSTRUCTIONS.AFTER INSTALLATION, retain the safety and operating instructions for future reference

1. HEED WARNINGS- Adhere to all warnings on the unit and in the operating instructions.

Installation and servicing must be performed by qualified personnel in accordance withlocal codes and regulations.

To prevent injury, this apparatus must be securely attached to the wall/ceiling inaccordance with the installation instructions.

To prevent damage to the interface board, follow standard industry precautions forelectrostatic discharge sensitive devices.

Consider using a UPS source to ensure satisfactory performance.

Using replacement parts or accessories other than the original manufacturers mayinvalidate the warranty.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

C A U T I O N

RISK OF ELECTRIC SHOCK

DO NOT OPEN


6/86

6

2. INSTALLATION

Install in accordance with the manufacturers instructions.

Installation and servicing should be performed only by qualified and experienced technicians to conform toall local codes and to maintain your warranty.

Do not install the unit in an extremely hot or humid location, or in a place subject to dust or mechanicalvibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

Any wall or ceiling mounting of the product should follow the manufacturers instructions for the mount usedand use best installation practice appropriate for the structure and material the mount is being attached to.

3. POWER SOURCES- This product should be operated only from the type of power source indicated on themarking label. If you are not sure of the type of power supplied to your facility, consult your product dealer orlocal power company.

4. HEAT- Situate away from items that produce heat or are heat sources such as radiators, heat registers, stoves,or other products (including amplifiers).

5. WATER AND MOISTURE- This product is designed for indoor use only. Do not use this unit near water or in anunprotected outdoor installation, or any area classified as a wet location.

6. MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer, or sold with the

product.7. ATTACHMENTS- Do not use attachments not recommended by the product manufacturer as they may result in

the risk of fire, electric shock, or injury to persons.

8. ACCESSORIES- Only use accessories specified by the manufacturer.

9. CLEANING- Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

10. SERVICING- Do not attempt to service this unit yourself as opening or removing covers may expose you todangerous voltage or other hazards. Refer all servicing to qualified service personnel.

11. REPLACEMENT PARTS- When replacement parts are required, be sure the service technician has usedreplacement parts specified by the manufacturer or have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock or other hazards.

Warranty and Service

Subject to the terms and conditions listed on the Product Warranty Card, during the warranty period Honeywell willrepair or replace, at its sole option, free of charge, any defective products returned prepaid.

In the event you have a problem with any Honeywell Video Systems product, please call Customer Service forassistance or to request a Return Merchandise Authorization (RMA)number. Be sure to have the model number,serial number, and the nature of the problem available for the technical service representative.

In the U.S.A. and Canada, call 1.800.796.2288.

Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without aclearly identified Return Merchandise Authorization (RMA) number may be refused.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal ofthis product (applicable in the European Union and other Europeancountries with separate collection systems). This product should bedisposed of, at the end of its useful life, as per applicable local laws,regulations, and procedures


7/86

ACUIXTMES Installation and Configuration Guide

Document 800-01949 Rev D 705/09

Contents

1 Introduction to the ACUIX ES PTZ Dome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

About Using This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Finding More Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ACUIX ES Terminology and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Flashback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Mimic Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Preset Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Privacy Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Sectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Dome Model Numbers and Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Important Information About Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Controller and Protocol Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19IntelliBus Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Cabling Recommendations and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20General Cautions and Notes for All Cable Installations . . . . . . . . . . . . . . . . . . . . . 20

Maximum Distances for Video, Data, Power, Contact and UTP Cabling . . . . . . . . . . . . 21Power Distances and Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Video CAT5 or Coaxial Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22RS485 Twisted-Pair Telemetry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Coax Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

About Setting Switches on the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2 Installing the ACUIX ES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installation Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Setting the Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

DIP Switch Default Settings and Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Selecting Video Over Coaxial Cable or Unshielded Twisted Pair (SW1) . . . . . . . . . . . . 33Setting the Baud Rate, Parity and Protocol (SW2 and SW3) . . . . . . . . . . . . . . . . . . 34Setting the RS485 Control Data Termination (SW5) . . . . . . . . . . . . . . . . . . . . . . . 35

Setting the Dome Address (SW4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Completing the Wiring Connections to Plugs 1, 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connecting the Power and RS485 Data Wiring . . . . . . . . . . . . . . . . . . . . . . . . . 37Connecting the Optional Contact Input Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . 39

Installing the Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Installing Indoor Pendant or Surface Domes. . . . . . . . . . . . . . . . . . . . . . . . . . . 40Installing In-Ceiling Domes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43


8/86

8

3 Configuring the ACUIX ES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Before You Begin Configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Step 1: Prepare the Controller and Monitor for Use . . . . . . . . . . . . . . . . . . . . . . . 47Step 2: Turn On (Power Up) the Dome and Find the Mechanical Home . . . . . . . . . . . . 48Step 3: Learn How to Use the Special Presets . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Step 4: Open the OSD Menu and Start Configuring . . . . . . . . . . . . . . . . . . . . . . . 50Configuring Display, Control, and Camera Menu Functions . . . . . . . . . . . . . . . . . . . . . . . 53

Configuring the Monitor and Text Display Settings . . . . . . . . . . . . . . . . . . . . . . . 53Configuring the Controller Settings - Pan and Tilt Reverse . . . . . . . . . . . . . . . . . . . 54Configuring the Pan, Tilt and Zoom (PTZ) and Dome Control Settings . . . . . . . . . . . . . 55Configuring the Image Quality and Video Display Settings . . . . . . . . . . . . . . . . . . . 56

Configuring Default Functions: Presets and Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Configuring Mimic Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Configuring Presets and Preset Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Configuring Privacy Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Configuring Sectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Configuring Contacts/Alarms (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

4 System Administration and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Resetting or Restoring the Dome to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Resetting the Scan and Dome/Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Restoring Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Resetting the Camera Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Clearing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Changing Dome Address, Protocol, Parity or Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . 73

Overriding the Logical Address on DIP Switch SW3-8. . . . . . . . . . . . . . . . . . . . . . 73Changing the Address, Protocol, Parity or Baud Rate Using the OSD . . . . . . . . . . . . . 74

Setting Boot Control (Debugging Mode) on Switch SW2-8 . . . . . . . . . . . . . . . . . . . . . . . . 74Working with Passwords and PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Enabling the User or Privacy Zone Login PIN . . . . . . . . . . . . . . . . . . . . . . . . . . 75Changing a 4-Digit User or Privacy Zone Login PIN . . . . . . . . . . . . . . . . . . . . . . . 75Recovering an Encrypted User or Privacy Zone Login PIN . . . . . . . . . . . . . . . . . . . 75Resetting a Privacy Zone Password (Diamond or IntelliBus Only) . . . . . . . . . . . . . . . 76

Sending Common Commands to all Domes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Enabling and Disabling the Broadcast Command Receive Mode. . . . . . . . . . . . . . . . 76

Displaying the Run Time Counter on the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Displaying System Information on the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Appendix A Pelco P_AD and Pelco D_AD Protocols . . . . . . . . . . . . . . . . . . . . . . . . . 79

Pelco P_AD and Pelco D_AD Protocol DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . 79Pelco P_AD and Pelco D_AD Special Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81


9/86


Document 800-01949 Rev D 905/09

Figures

Figure 1-1 ACUIX ES Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 2-1 Location of Switches SW2, SW3 and SW4 and RS485 Termination Switch SW5RS485 Termina-tion29

Figure 2-2 Example of a DIP Switch Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 2-3 Video Selection Switch SW1 and Wiring P1, P2, and P3 Locations . . . . . . . . . . . . . 30Figure 2-4 RS485 Daisychain Wiring (up to 32 domes): Control at One End . . . . . . . . . . . . . . 38

Figure 2-5 Surface and Indoor Pendant Dome Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 2-6 Indoor Pendant Ceiling and Wall Mount Dimensions . . . . . . . . . . . . . . . . . . . . . 41

Figure 2-7 Insert Cover into Skirt or Top Cap and Turn to Secure . . . . . . . . . . . . . . . . . . . . 42

Figure 2-8 In-ceiling Dome Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 2-9 In Ceiling Scan Assembly with Switch, Plugs and BNC Connector . . . . . . . . . . . . . 44

Figure 2-10 Stagger the Wing Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 2-11 Inside the In-ceiling Scan Assembly and Housing . . . . . . . . . . . . . . . . . . . . . . 45

Figure 3-1 On-Screen Menu Layout Sony FCB-EX45C Color Camera. . . . . . . . . . . . . . . . . . 52


10/86

10


11/86


Document 800-01949 Rev D 1105/09

Tables

Table 1-1 ACUIX ES Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 1-2 ACUIX ES Dome Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 1-3 Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Table 1-4 Video, Data, Power, Contact and UTP Cabling . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 1-5 Power Distances for 24V AC or 12V DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Table 1-6 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 1-7 Typical 75 Ohm Coaxial Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 1-8 CAT5 Cabling and UTP Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Table 2-1 Default DIP Switch Settings for NTSC or PAL Camera Models . . . . . . . . . . . . . . . . 31

Table 2-2 Typical DIP Switch Settings by Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Table 2-3 DIP Switch Baud Rate and Parity Settings (SW2 1 - 6) . . . . . . . . . . . . . . . . . . . . 34

Table 2-4 DIP Switch Protocol Settings (SW3 1 - 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 2-5 Address Binary Conversion Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table 2-6 Power and Data Plug P1 on the 5-Pin Connector . . . . . . . . . . . . . . . . . . . . . . . 37

Table 2-7 Contact Wiring 3 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 2-8 UTP and Contact Wiring 9 Pin (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 2-9 ACUIX ES Pendant Ceiling and Wall Mount Specifications . . . . . . . . . . . . . . . . . . 41

Table 3-1 Display Options at Dome Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 3-2 Special Presets Based on Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Table 3-3 Mimic Tour Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 3-4 Preset and Preset Tour Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Table 3-5 Privacy Zone Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Table 3-6 Sector Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Table 3-7 Contact Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Table 3-8 Program Contact Submenu: Contact States . . . . . . . . . . . . . . . . . . . . . . . . . 69

Table 4-1 DIP Switch SW3 Setting by Protocol to Force a Reading . . . . . . . . . . . . . . . . . . . 73

Table 4-2 OSD System Information Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77


12/86

12


13/86


05/09

1

Introduction to the ACUIX ES PTZ Dome

In this section:

About Using This Guide, page 13, including where to find more information and thisdocuments typographical conventions.

ACUIX ES Terminology and Features, page 14, including the features that areconfigured using the on-screen display (OSD).

Dome Model Numbers and Camera Specifications, page 17.

Important Information About Protocols, page 18, including compatibility andinformation about the IntelliBus protocol.

Cabling Recommendations and Cautions on page 20including cautions, maximumdistances to the dome, power distances, information about video CAT5 or coaxialcables, RS485 twisted pair telemetry, and coax control.

About Setting Switches on the Mainboard, page 25.

About Using This Guide

Finding More Information

Refer to the on-line product library to access electronic documents in PDF formatincluding data sheets, quick references, installation and user guides, specifications, andproduct notices. http://www.honeywellvideo.com/support/literature/index.html

Typographical Conventions

This document uses these typographical conventions:


14/86

14


ACUIX ES Terminology and Features

Font What it represents Example

Lucida Text strings displayed on the OSD menu. The messageUnauthorizeddisplays.

(object) entered.

Swiss721BT Bold

Words or characters that are typed.

Pressing a key on the controller.

Selecting a menu item from the OSD.

Enter the password.

Press and hold wash.

Select 2 Control Options > 1 PASS.

Italic Cross-reference to external source.

Cross-reference within document.

Refer to the Honeywell Video websitehttp://www.honeywellvideo.com/

See Introduction to the HDX-LT PTZDome on page 13

Table 1-1 ACUIX ES Terminology

Term Definition

dome The complete installed product including the housing, lower dome, andthe scan assembly.

scan assembly The combination of firmware, electrical and mechanical components

including the camera. The scan assembly is either pre-installed orinstalled separately into the housing and enclosed by a lower dome. Thescan assembly is a component of a dome.

camera The particular camera model (for example, the Sony FCB EX45C)purchased. The camera is a component of the scan assembly.

housing The in-ceiling, indoor or outdoor pendant and surface mount upperenclosure. Housing is a hardware component of the dome.

mount The hardware used to mount the housing to the applicable surface (forexample, a ceiling or wall). The mount is a hardware component used witha specific type of housing.

lower dome The clear or colored enclosure that covers the scan assembly andattaches to the housing. The lower dome is a hardware component of the

dome.


15/86


Document 800-01949 Rev D 1505/09

Figure 1-1 ACUIX ES Hardware Components

Contacts

Contacts can detect a door opening or window breakage, for example. Using the on-screendisplay (OSD), you can program up to four normally open or closed conditions to activatea preset, preset tour or mimic tour. For wiring connections, see Connecting the OptionalContact Input Wiring on page 39and for OSD settings, see Configuring Contacts/Alarms(Optional) on page 67.

Note The term contactandalarmare used interchangeably to mean the same

thing.Alarmis displayed on the OSD, although contactis a better descriptionsince it is not an audible alarm but a change in electrical state to the contactsresulting in a programmed response.

Flashback

Use the Flashback feature to toggle between two saved positions and quickly return to ascene of interest.

Flashback is available using a controller. When you press Flashback, it saves the scene(Scene A) as a Flashback. When you move to the next scene (Scene B) and pressFlashback again, it saves Scene B and returns the dome to Scene A. If the operator pressesFlashback a third time (without manually moving to a new scene), the dome returns toScene B. The dome only saves and toggles between two scenes at a time, except whenFlashback is used during a preset tour. See Using the Flashback Preset on page 50.

Housing

Lower dome

Dome

Pendant mounts


16/86

16


Mimic Tours

A mimic tour saves the pan, tilt, and zoom commands performed by a user. When a mimictour is started, the dome replays the saved commands. A mimic tour is useful when

operators are interested in scanning slowly to a particular area on a regular basis. You canprogram up to three (3) mimic tours up to 120 seconds (two minutes) each. See ConfiguringMimic Tours on page 60.

Presets

The ACUIX ES supports over 64 presets, and each preset can have a 24-characteralphanumeric name. There are two types of presets: A special preset that is a shortcut to afunction, for example, opening the OSD menus; and an operator created/programmed setof commands (pan, tilt, zoom, focus, and iris setting). The programmed preset is recalledin response to a contact or set as the default function when the dome is idle for a specified

time. Individual presets can also be part of preset tours. See Configuring Presets and PresetTours on page 61.

Preset Tours

Up to three (3) preset tours can be programmed for each dome and up to 24 presets, withvelocity settings and dwell times for each preset, can be programmed into every presettour. Preset tours can be started by an operator, in response to a contact, or programmedas a default function when the dome is idle for a specified amount of time.

Operators can run the preset tour once or continuously. If an operator runs a preset tourcontinuously, the dome goes from the last preset to the first preset. The preset tour repeatscontinuously until an operator manually controls the dome (pan, tilt, zoom, focus, or iris) orthe dome receives a preset, preset tour, mimic tour, or find home command. SeeConfiguring Presets and Preset Tours on page 61.

Privacy Zones

Privacy zones enable operators to restrict the view in a specific area, for example privateproperty, windows visible across alleyways, swimming pools, or dressing rooms. A mask(colored box) covers the video display when the dome acknowledges it is passing through

a privacy zone. Privacy Zone data is stored in nonvolatile memory, which saves the datawhen the dome is not powered.

The number of available privacy zones is camera dependent. For the Sony FCB EX-45Ccamera, up to 24 privacy zones can be programmed. See Configuring Privacy Zones onpage 63.


17/86


Document 800-01949 Rev D 1705/09

The use of a Privacy Zone password or PIN is available depending on the protocol:

For MAXPRO-mode, VCL, VCL UTC, Pelco P and Pelco D protocols, privacy zoneprogramming is protected by a four digit numeric PIN. The default PINis 1000.

Diamond/IntelliBus: Up to 24-alphanumeric characters can be programmed as apassword. The default password is a blank line.

See Working with Passwords and PINS on page 75.

Sectors

Sectors are used for labeling an area monitored by a dome. For example, when you aremonitoring an exit door, add the label ExitDoor. Whenever the dome is positioned over thisarea, ExitDoordisplays on the monitor.

You can label up to 16 sectors and the sectors can overlap. If the operator positions the

dome where one or more programmed sectors overlap, the dome sequences between theSector titles on the video display for 1.5 seconds per Sector. See Configuring Sectors onpage 66.

Dome Model Numbers and Camera Specifications

Table 1-2 ACUIX ES Dome Models

Description NTSC Model

Number

PAL Model

Number

In-ceiling, UTP, 18X CLR, smoke lower dome, white trim ring HDVANDASW HDVAPDASW

In-ceiling, 18X CLR, smoke lower dome, white trim ring HDVANDBSW HDVAPDBSW

In-ceiling, UTP, 18X CLR, clear lower dome, white trim ring HDVANDACW HDVAPDACW

In-ceiling, 18X CLR, clear lower dome, white trim ring HDVANDBCW HDVAPDBCW

Surface Mount or Pendant, 18X CLR, smoke lower dome HDVANSAS HDVAPSAS

Surface Mount or Pendant, UTP, 18X CLR, smoke lower dome HDVANSBS HDVAPSBS

Surface Mount or Pendant, 18X CLR, clear lower dome HDVANSAC HDVAPSAC

Surface Mount or Pendant, UTP, 18X CLR, clear lower dome HDVANSBC HDVAPSBC


18/86

18


Important Information About Protocols

In general, protocols allow cross compatibility between products and manufacturers.Because the ACUIX ES PTZ dome is designed to work with a variety of controllers, DVRsand other hardware, deciding what protocol to use when setting up a system is challenging.It is also not possible to describe all the tasks using all combinations of protocols andhardware. Therefore, these instructions are a supplement to the hardware users guides andare based on the use of the Honeywell HJZTP joystick controller.

Table 1-3 Camera Specifications

Item 18X Color Camera

Image sensor 1/4" Ex-view HAD CCDLens 18x optimal zoom, f=4.1mm (wide) to 73.8mm

(tele), F1.4 to F3.0

Horizontal resolution >470 TVL (NTSC)>460 TVL (PAL)

Moveable IR filter No

Wide Dynamic Range (WDR) No

Digital Zoom 12X (216X total zoom)

Angle of View (H) 48 (wide end) to 2.8 (tele end)

Sync System Internal/AC line lock

Minimum Illumination 0.7 lux

S/N Ratio > 50dB

Electronic Shutter 1/1 to 1/10, 000 sec

White Balance Auto, ATW, Indoor, Outdoor, Manual

Gain Auto/Manual

Backlight Compenstation (BLC) On/Off/Auto

Focusing System Auto/Manual


19/86


Document 800-01949 Rev D 1905/09

Note The HJZTP Controller User Guide indicates it can be set to either VCL orDiamond protocols. The ACUIX ES default protocol is MAXPRO-mode forNTSC and VCL RS485 protocol for PAL.When in NTSC andfor the HJZTP

controller ONLY, MAXPRO-mode can be considered exactly the same asDiamond protocol.From the users perspective, the MAXPRO-mode allowsaccess to the same special presets as with the VCL protocol.

If other controllers, DVRs or protocols are used, MAXPRO-mode, Pelco P or Pelco Dprotocols also operate in a similar way as described for the VCL protocol. That is tosay, how you access the special presets and on-screen display (OSD) is approximately thesame.

Controller and Protocol Compatibility

The ACUIX ES is compatible with the following controllers and protocols:

HJZTP controller using the VCL or MAXPRO-mode protocols

HMAX082/HMAX162 Matrix Switcher and HKJMMTP controller using VCL UTP / coaxcontrol protocol

Pelco P and Pelco D third party protocols and controllers

HEGS5000/5001 controller using Diamond protocol

IntelliBusTMprotocol

IntelliBus Protocol

When ACUIX ES is network connected to a PC-based DVR (such as the Honeywell RapidEye) and set to the IntelliBus protocol, you can:

Download an ACUIX ES configuration to a PC for later use: After completing the userprogramming of the dome (presets, mimic tours, preset tours, and privacy zones), you canupload the configuration data to a PC for safekeeping.

Upload an ACUIX ES configuration to another dome of the same camera model: Theconfiguration can be saved on a PC and uploaded to a replacement dome if required. TheACUIX ES configuration has camera model specific parameters so the configurationuploads (retrieving data from a faulty dome) and downloads (sending data to a new dome)must be between two domes with the same camera model.

Upgrade the firmware to one or more ACUIX ES PTZ domes in your network.

For detailed information about these options using the IntelliBus protocol, refer to the RapidEye System Administrator Guide and the Rapid Eye Installation Guide.


20/86

20


Cabling Recommendations and Cautions

Cable preparation should be completed prior to the installation. Each dome requires 24VAC at 1 A or 12V DC at 1.5 A. The power supply should be located as close to the dome aspossible for service and electrical isolation purposes. In situations where the power supplyhas to be installed remotely, seeTable 1-5for wire gauges and distances. See Table 1-6forthe recommended power supplies for use with the indoor ACUIX ES.

If required, refer to other hardware installation guides to determine cabling requirementsbased on the individual configuration. See Finding More Information on page 13.

General Cautions and Notes for All Cable Installations

Note For all cables:

The quality and specification of any cable used has a direct effect on thequality of the video signal at the control equipment end of the system.Compromising the cable quality and specification can lead to poor videoquality and system performance.

When other cables cannot be avoided, run cables perpendicular to eachother, not alongside, and keep this distance as short as possible.

Faulty cable or wiring can cause all domes to fail or malfunction.

If several domes are powered from a single power source (multiple tap) and noiseis experienced on the TP video output, then an isolated power supply should beused to correct the problem.

Never run the cables close to potential sources of electromagnetic interferencesuch as motors, dimmers, and high-speed data trunk cables.

For CE compliance, the power supply must be connected to a CE-approved 240VUPS (uninterruptible power supply). See Table 1-6for a list of the power supplieswhich must be used to meet FCC and UL requirements.


21/86


Document 800-01949 Rev D 2105/09

Maximum Distances for Video, Data, Power, Contact and UTP Cabling

Note The termsshieldedand unshieldedare interchangable withscreenedandunscreened, respectively.

Note UTP is a general term for all cabling systems used for transmission ofunshielded data and providing connectivity on a network. A UTP cable cancontain multiple pairs of twisted cables. Commonly used for telephonecabling and 10BaseT and 100BaseT networks.

Installation of cable gauges and distances that are outside the scope of Table 1-4andTable 1-5are undertaken solely at the installers risk and responsibility.

Table 1-4 Video, Data, Power, Contact and UTP Cabling

Type Recommended Cable Maximum Distance

Video Coaxial cable - RG59/U

Connector - BNC crimp onfor RG59/U

1000 feet (305 meters)

Data One shielded twisted pair,RS485 cable including CAT5or better


Power 18 AWG 2-conductor See gauge chart for eachdome

Contact (Alarm) 20 gauge unshielded twistedpair

10,000 feet (3048 meters)

UnshieldedTwisted Pair (UTP)

Video

CAT5 or better1 twisted pair for video



22/86

22


Power Distances and Supplies

Video CAT5 or Coaxial Cables

Table 1-5 Power Distances for 24V AC or 12V DC

Power Supply Wire Gauge (AWG) mm2 Feet Meters

24V AC

24 0.21 35 10

Doubled 24 0.21 x 2 70 20

18 0.8 145 45

16 1.3 230 70

14 2.1 360 110

12V DC

24 0.21 15 5

Doubled 24 0.21 x 2 35 10

18 0.8 70 20

16 1.3 115 35

14 2.1 180 55

Table 1-6 Power Supplies

Application Specification

Internal - 1 per ACUIX ES 24V AC 1 amp x 1, or12V DC 1.5 amp x 1

Internal - up to 8 ACUIX ES 24V AC 1 amp x 8, or12V DC 1.5 amp x 8

Always keep coaxial cables away from all other cables and run them in completeisolation wherever possible.

If running a separate CAT5 cable specifically for CCTV, ensure it is clearlyidentified to prevent confusion with network and other structured cabling.

Use Krone type junction boxes where CAT5 joints are necessary. These boxes aresupplied with labeling for all terminals. A special tool is required to insert cablesinto Krone junction terminals.

Also see General Cautions and Notes for All Cable Installations, page 20.


23/86


Document 800-01949 Rev D 2305/09

Video Coaxial Cable

Video CAT5 Cable (UTP Transmission)

CAT5 cabling for video transmission allows multiple domes to be transmitted down thesame multicore CAT5 cable without dome video interference or crosstalk. Table 1-8showsthe distances and UTP options suitable for ACUIX ES domes. Requires one wire pair perdome. It can support up to four domes on a single CAT5 cable.

Adhere as closely as possible to the following recommendations when installing with CAT5cable and UTP receiving equipment.

A UTP receiver module must be used at the control end of the system for every domethat is transmitting video via CAT5. A UTP hub can be used to receive up to 16 domesusing CAT5 cable.

PTZ telemetry is possible when a passive UTP receiver module or hub is used at the

control end of the system. If an active receiver is used at the control end of thesystem, then RS485 telemetry must be used. This requires another single twisted pairper dome.

When wiring via twisted pair, always ensure that you are actually using a twisted pairby examining the cable. Failure to use wires from the same pair leads to noiseintroduction and subsequent video and telemetry problems.

The CAT5 cable used must not be shielded/screened in any way, either by foil,braided shield, or any other means. The use of any cable other than unshielded CAT5may lead to a reduction in performance and is solely the responsibility of the installer.

Table 1-7 Typical 75 Ohm Coaxial Cable Specifications

Type Conductor Application

RG59 1/0 0.58mm Main internal cable runs. May also be used externally incontainments or when damage is unlikely. Not veryflexible.

URM70 7/0 0.19mm Patch cables from main runs to equipment. Equipmentinterconnection. Flexible and useful for tight bends.

CT125 1/0 1.2mm Duct/containment rated cable for external main cableruns. Some grades are suited for direct burial.


24/86

24


RS485 Twisted-Pair Telemetry

When using RS485 twisted-pair telemetry, the video signal is transmitted via a coaxial orCAT5 twisted pair cable and the control data (telemetry) information is a twisted-pair cable.

RS485 twisted-pair telemetry cabling is installed and wired as a network that consists of oneor more daisychains. When more than one daisychain is installed, an RS485 telemetrydistribution unit must be installed to broadcast telemetry data across the entire RS485network. Multiple distribution units can be installed on the RS485 network to allow forcomplex wiring arrangements.

The recommended RS485 cable is a 20-gauge unshielded twisted pair cable. This cable isa single twisted-pair overall shield and the maximum distance for a daisychain is up to 4000feet (1219 meters). These cables are available in a series of overall outer sheaths fromstandard internal usage finishes to external containment and direct burial types.

Table 1-8 CAT5 Cabling and UTP Options

Distance Receiver model and Description Video Telemetry

(Telemetry over

Video)

Up to 500 feet(150 meters)

NV-212A video transceiver. Cablemust be within the same building asthere is no transient protection

Yes

Up to 1000 feet(300 meters)

NV213A video transceiverNV-813A 8-port passive hubNV-1613A 16-port passive hub

Yes

Up to 3000 feet(1 kilometer)

NV652R active receiverNV862 8-port active receiverNV-1662R 16-port active receiver

No. Telemetry mustbe via RS485 usinganother pair

Star wiring configurations are acceptable with the use of a code distribution unitsuch as Honeywell HDCD8TP.

Always keep RS485 data cables away from all other cables and run them incomplete isolation whenever possible.

Couple all data cable shields to data ground at the control point end only. Thecable shields should not be connected at any other point.

Connect the cable shield at the controller and connect the cable shield through anyjunction boxes installed, but do not connect the cable shield to the dome.

Also see General Cautions and Notes for All Cable Installations, page 20.


25/86


Document 800-01949 Rev D 2505/09

Coax Control

The ACUIX ES domes support telemetry control over coaxial cable. The dome must be setto VCL UTC for coaxial telemetry. The telemetry mode is auto sensing. If no RS485

connection is sensed, then the dome operates via coaxial telemetry.

Up-the-coax operation of up to 1000 feet (300 meters) is possible with the appropriatecoaxial cable. See Table 1-4for recommended coaxial cables.

About Setting Switches on the Mainboard

The ACUIX ES has switches SW1, SW2, SW3, SW4 and SW5 that require setting dependingon the installation. It is also important that settings match the control equipment settings.See Setting the Switches on page 28for defaults and detailed information.

Use these switches to:

Set the video selection to UTP or Coax video enabled (SW1). Seepage 33.

Set baud rate and parity (SW2 positions 1 to 6). Seepage 34.

Set the protocol (SW3 positions 1 to 5). Seepage 34.

Set the dome address (SW4 positions 1 to 8). Seepage 35.

Set the RS485 termination (SW5). Seepage 35.

The switches also control advanced settings to:

Restore the factory default settings (SW3-7). Seepage 73.

Override the switch settings for the logical address and protocol (SW3-8). Seepage 73.

Set debugging mode/boot control (SW2-8). Seepage 74.


26/86

26



27/86


05/09

2

Installing the ACUIX ES

In this section:

Installation Warnings and Cautions, page 27.

DIP Switch Default Settings and Locations, page 28.

Selecting Video Over Coaxial Cable or Unshielded Twisted Pair (SW1), page 33.

Setting the Baud Rate, Parity and Protocol (SW2 and SW3), page 34.

Setting the RS485 Control Data Termination (SW5), page 35.

Setting the Dome Address (SW4), page 35.

Connecting the Power and RS485 Data Wiring, page 37.

Connecting the Optional Contact Input Wiring, page 39.

Installing Indoor Pendant or Surface Domes, page40.

Installing In-Ceiling Domes, page43.

Installation Warnings and Cautions

Note Also see Cabling Recommendations and Cautions, page 20.

All installations must be performed by qualified technical personnel and must bein accordance with all national and local mechanical and electrical codes.

Ensure the mounting surface and installation hardware can hold the combinedweight of the scan assembly, housing, lower dome and mount.

To prevent damage to the interface board, follow standard industry precautionsfor electrostatic discharge-sensitive devices.


28/86

28


Setting the Switches

Also see Cabling Recommendations and Cautions on page 20and System Administrationand Settings on page 71.

For the location of the different switches and plugs, see Figure 2-1and Figure 2-3. Forexamples of DIP switch settings, see Figure 2-2and Table 2-2.

Note For Pelco P_AD and Pelco D_AD switch settings and special presets, seeAppendix A.

DIP Switch Default Settings and Locations

Note If there are invalid protocol or baud rate settings on SW2 or SW3, the systemdefaults to MAXPRO-mode protocol (NTSC) or VCL RS485 (PAL) and a 9600baud rate (NTSC and PAL).

Note There is a DIP switch setting label located on the scan assembly that you canrefer to while setting the switches.

To make good wire contact and ensure the wire does not short to adjacent wires,fully insert the wire in the hole on the terminal strip.

Ensure there are no bare wires touching or faulty operation may occur.

Ensure the cabling does not interfere with the rotation of the scan assembly.

Each dome requires a 24V AC at 1 A or 12V DC at 1.5A 15% power sourcewhen measured at the dome. To maintain 24V AC at 1 A or 12V DC at 1.5A 15% at each dome, the proper wire size for the distance and the number ofdomes must be determined. See Maximum Distances for Video, Data, Power,Contact and UTP Cabling on page 21.


29/86


Document 800-01949 Rev D 2905/09

Figure 2-1 Location of Switches SW2, SW3 and SW4 and RS485 TerminationSwitch SW5RS485 Termination

Figure 2-2 Example of a DIP Switch Setting

SW4

SW2

SW3

Skirt / scan

assembly SW5 on other side

SW5

ON OFFSkirt / scan

assembly

SW2, 3 and 4 onother side

ON

OFF

Positions 1, 2, 4, 6, and 7 set to OFF

Positions 3, 5, and 8 set to ON

OFF | OFF | ON | OFF | ON | OFF | OFF | ONThis DIP Switch setting is:


30/86

30


Figure 2-3 Video Selection Switch SW1 and Wiring P1, P2, and P3 Locations

ON = UTP Video Enabled

OFF = COAX Video Enabled

SW1 Video Selection

The base of the pendant, surfacemount or in- ceiling housing and scanassembly has these switches andplugs. Shown is the pendant orsurface mount. Seepage 43for anexample of the in-ceiling.

Contact Wiring Plugs P2 and P3

Power and Data Wiring Plug P1

P1 P2

P3

BNC Connector


31/86


Document 800-01949 Rev D 3105/09

Note NTSC or PAL settings are camera model dependent. See Table 1-2ACUIX ESDome Models, page 17for a list of available NTSC or PAL cameras.

Table 2-1 Default DIP Switch Settings for NTSC or PAL Camera Models

Setting NTSC Defaults PAL Defaults Switch and Available

Positions

Baud rate 9600 9600 SW2 (1 to 4)

Parity Even No parity SW2 (5 and 6)

Protocol MAXPRO-mode VCL 485 SW3 (1 to 5)

Address 1 1 SW4 (1 to 8)

RS485 Termination Not Terminated (OFF) Not Terminated (OFF) SW5

Video Selection COAXIAL VideoEnabled (OFF)

COAXIAL VideoEnabled (OFF)

SW1

Miscellaneous Defaults*

Reserved OFF OFF SW3 (6)

Restore Factory Defaults OFF OFF SW3 (7)

Overriding the LogicalAddress

ON ON SW3 (8)

Reserved OFF OFF SW2 (7)

Debugging/boot control OFF OFF SW2 (8)

* These are advanced switch settings and it is not recommended to make changes to these defaults. SeeSystem Administration and Settings on page 71for more information.


32/86

32


Table 2-2 Typical DIP Switch Settings by Protocol

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

Intellibus

38400baud,noparity

OFF

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFFO

FF

ON

MAXPRO*

9600baud,evenparity*

OFF

OFF

ON

OFF

ON

OFF

OFF

OFF

OFF

ON

OFF

OFF

OFF

OFFO

FF

ON

VCL-RS485**

9600baud,noparity**

OFF

OFF

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

OFF

OFFO

FF

ON

VCLUTC

9600baud,noparity

OFF

OFF

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

OFF

OFF

OFFO

FF

ON

Diamond

9600baud,evenparity

OFF

OFF

ON

OFF

ON

OFF

OFF

OFF

ON

OFF

OFF

OFF

OFF

OFFO

FF

ON

PelcoP

4800baud,noparity

(d

efaultforP-typecontrol)

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

ON

OFF

ON

OFF

OFF

OFFO

FF

ON

PelcoD

2400baud,noparity

(d

efaultforD-typecontrol)

OFF

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

OFFO

FF

ON

*NTSCcameramodelsdefaultsettings.

**PALcameramo

delsdefaultsettings.

Pro

toco

l

Bau

dan

dPari

ty

Descrip

tion

SW

2-

Bau

dan

dPari

tySe

ttings

SW3

Pro

toco

lSe

tting


33/86


Document 800-01949 Rev D 3305/09

Selecting Video Over Coaxial Cable or Unshielded Twisted Pair (SW1)

1. Locate the video selection switch SW1 on the base of the scan assembly. SeeFigure 2-3.

2. If required, change from the OFF default by carefully placing the switch in the requiredvideo selection position:

(Default)COAX Video Enabled: Switch OFF (away from ON)Unshielded twisted pair (UTP) video balun disabled, to be used with normal 75Ohm coax video operation.

UTP Video Enabled:Switch ON.UTP video balun enabled, to be used with 120 Ohm UTP video operation.

Control Over Coaxial Cable

The control equipment adds the data signal to the video coaxial cable. In this case, thereare no connections made at Data+ and Data on the terminal strip P1.

Video Over Coaxial Cable: Coax Video Enabled

The video must be terminated in 75 Ohm at the last video device. If the video is not

terminated or is double terminated, the resulting picture is poor and ghosting is displayed.

Video Over Unshielded Twisted Pair: UTP Video Enabled

If the UTP option is selected, the video is run on UTP wire and the BNC connector is not

used. The video is connected at plug P3, pins 1 and 2 (see Figure 2-3). A UTP-compatiblereceiver is required at the monitor to view and/or record the images.

For control over coaxial cable, the ACUIX ES must be set to VCL video telemetry (controlover coax) protocol and must be controlled using an HMAX082 or HMAX162 control unitwith HKJMMTP joystick controller.

The video on the UTP wire cannot be daisychained.


34/86

34


Setting the Baud Rate, Parity and Protocol (SW2 and SW3)

1. Set the baud rate and parity on SW2. See Figure 2-1. Carefully place the SW2 switchin the required positions if different from the defaults.

To make changes to the default, use Table 2-3and see Figure 2-2and Table 2-2for examples.

2. Set the protocol on SW3. See Figure 2-1. Carefully place the SW3 switch in therequired positions if different from the defaults.

To make changes to the default, use Table 2-4and see Figure 2-2and Table 2-2for examples.

Table 2-3 DIP Switch Baud Rate and Parity Settings (SW2 1 - 6)

Baud Rateand Parity

Values

Baud Rate Switch Position Parity SwitchPosition

1 2 3 4 5 6

600 OFF OFF OFF OFF

1200 ON OFF OFF OFF

2400 OFF ON OFF OFF

4800 ON ON OFF OFF

9600 OFF OFF ON OFF

19200 ON OFF ON OFF

38400 OFF ON ON OFF

57600 ON ON ON OFF

115200 OFF OFF OFF ON

None OFF OFF

Even ON OFF

Odd OFF ON


35/86


Document 800-01949 Rev D 3505/09

Setting the RS485 Control Data Termination (SW5)

1. Locate SW5. See Figure 2-1.

2. If required, change from the default and carefully place the SW5 switch in the requiredtermination position:

(Default)Not terminated: SwitchOFF (away from ON).

Terminated in 120 Ohm: SwitchON.

Setting the Dome Address (SW4)

Note Each dome requires a unique address. The ACUIX ES can be addressed from001 to 255. The default address is 001.

1. Locate SW4. See Figure 2-1.

Carefully place the SW4 switch in the required ON/OFF positions based on thedome address. See Table 2-5for a partial list of the address settings andFigure 2-2for a DIP switch example.

Table 2-4 DIP Switch Protocol Settings (SW3 1 - 5)

Protocol Name Switch Positions

1 2 3 4 5

IntelliBus OFF OFF OFF OFF OFF

MAXPRO-mode OFF ON OFF OFF OFF

VCL - RS485 ON ON OFF OFF OFF

VCL UTC OFF OFF ON OFF OFF

Pelco P ON OFF ON OFF OFF

Pelco D OFF ON ON OFF OFF

Diamond ON OFF OFF OFF OFF


36/86

36


Table 2-5 Address Binary Conversion Table

Binary Value/Dome

Address

SW4-1

(1)

SW4-2

(2)

SW4-3

(4)

SW4-4

(8)

SW4-5

(16)

SW4-6

(32)

SW4-7

(64)

SW4-8

(128)

1 ON OFF OFF OFF OFF OFF OFF OFF

2 OFF ON OFF OFF OFF OFF OFF OFF

3 ON ON OFF OFF OFF OFF OFF OFF

4 OFF OFF ON OFF OFF OFF OFF OFF

5 ON OFF ON OFF OFF OFF OFF OFF

6 OFF ON ON OFF OFF OFF OFF OFF

7 ON ON ON OFF OFF OFF OFF OFF

8 OFF OFF OFF ON OFF OFF OFF OFF

9 ON OFF OFF ON OFF OFF OFF OFF

10 OFF ON OFF ON OFF OFF OFF OFF

11 ON ON OFF ON OFF OFF OFF OFF

12 OFF OFF ON ON OFF OFF OFF OFF

13 ON OFF ON ON OFF OFF OFF OFF

14 OFF ON ON ON OFF OFF OFF OFF

15 ON ON ON ON OFF OFF OFF OFF

16 OFF OFF OFF OFF ON OFF OFF OFF

17 ON OFF OFF OFF ON OFF OFF OFF

18 OFF ON OFF OFF ON OFF OFF OFF

19 ON ON OFF OFF ON OFF OFF OFF

20 OFF OFF ON OFF ON OFF OFF OFF

21 ON OFF ON OFF ON OFF OFF OFF

22 OFF ON ON OFF ON OFF OFF OFF

23 ON ON ON OFF ON OFF OFF OFF

24 OFF OFF OFF ON ON OFF OFF OFF

25 ON OFF OFF ON ON OFF OFF OFF

26 OFF ON OFF ON ON OFF OFF OFF27 ON ON OFF ON ON OFF OFF OFF

28 OFF OFF ON ON ON OFF OFF OFF

29 ON OFF ON ON ON OFF OFF OFF

30 OFF ON ON ON ON OFF OFF OFF

0(diagnostic mode only)

OFF OFF OFF OFF OFF OFF OFF OFF


37/86


Document 800-01949 Rev D 3705/09

Completing the Wiring Connections to Plugs 1, 2 and 3

Note Review Cabling Recommendations and Cautions, page 20prior to completingthis section.

Connecting the Power and RS485 Data Wiring

The power and RS485 data wiring plugs for the 5-pin connection are located on the scanassembly. See Figure 2-3onpage 30for the location. Also see Power Distances andSupplies, page 22and RS485 Twisted-Pair Telemetry, page 24for more information.

Note Ensure the correct connections are made with data pins 4 (-) and 5 (+)otherwise polarity can be an issue.

A good earth ground must be connected at the 5-pin connector, P1, pin 2. Surge, ESD

and EMC performance will be compromised if the unit is not connected to a good earthground.

Table 2-6 Power and Data Plug P1 on the 5-Pin Connector

PIN Description

1 24V AC input A or 12V DC (+) or (-)

2 ESD (electrostatic discharge) grounding

3 24V AC input B or 12V DC (+) or (-)

4 RS485 data (-) communication signal

5 RS485 data (+) communication signal


38/86

38


RS485 Termination and Wiring Switch SW5

The factory RS485 termination default is unterminated. RS485 communication is terminatedusing switch SW5.

One pair of shielded twisted pair RS485 wire or one pair of unshielded twisted pairwire can be used for RS485 data.

The data lines can be daisychain wired (see Figure 2-4) from the control output.Daisychain wiring consists of up to 32 domes per data run with the control output ateither end of the run. The last dome on the end of the data run must be terminatedand all intermediate domes unterminated.

Note Each RS485 port on the HDCC8TP must be treated individually as if each oneis on a separate piece of equipment.

Figure 2-4 RS485 Daisychain Wiring (up to 32 domes): Control at One End

For the RS485 daisychain wiring, the data cable shield/screen should be carriedthrough all units by connecting the cable shields together. Connect the cable shieldat the control unit.

Last domeTerminated

Dome 1Not terminated

Dome 2Not terminated

Domes 3 to 31

Not terminated

Control equipment

SW5 OFF SW5 OFF SW5 ON


39/86


Document 800-01949 Rev D 3905/09

Connecting the Optional Contact Input Wiring

Note The contact cabling should not be terminated until standard operation of thedome is tested.

The plugs for the 3- and 9-pin connections to the contact inputs are located on the scan

assembly. See Figure 2-3onpage 30for the location. If contact devices are connected tothe dome, they should not be connected to the contact connector until all domefunctionality has been fully tested. Contact device activations could cause confusion duringthe initial testing stages.

See Tables 2-7and 2-8for wiring information.

All contact input connections MUST be passive contacts.

Table 2-7 Contact Wiring 3 Pin

Pin P2 (3 pin)

1 Contact input 1

2 Contact input common

3 Contact input 2

Table 2-8 UTP and Contact Wiring 9 Pin (Optional)

Pin P3 (9 pin)

1 UTP + signal

2 UTP - signal

3 Contact input 3

4 Contact input 4

5 Contact input 56 Contact input 6

7 Contact input 7

8 Contact input 8

9 Contact input common


40/86

40


Installing the Dome

Note Each dome requires a 24V AC at 1 A or 12V DC at 1.5A 15% power sourcewhen measured at the dome. To maintain 24V AC at 1 A or 12V DC at 1.5A 15% at each dome, the proper wire size for the distance and the number ofdomes must be determined.

Follow the instructions to install either an:

Indoor pendant or surface mount.

In-ceiling for a dropped or hard ceiling.

Installing Indoor Pendant or Surface Domes

The following explains how to install either a ceiling or wall mount with the indoor pendantor surface mount. The cover and lower dome installation is the same for both. SeeFigure 2-6.

Note All ACUIX ES pendant/surface mount shipments include both the skirt and topcap. Use the part appropriate to the installation; the other is a spare part.

In addition to the other items normally supplied by the installer, the following may berequired for the surface installation:

Tape or plastic channel to prevent dust and material from falling from the ceiling.

Mounting hardware appropriate for your installation surface.

Figure 2-5 Surface and Indoor Pendant Dome Layout

Top cap

Cover

Lower dome

Skirt

Cover

Lower dome

Field wiring access hole

Surface Mount Indoor Pendant


41/86


Document 800-01949 Rev D 4105/09

Figure 2-6 Indoor Pendant Ceiling and Wall Mount Dimensions

14.76(375.0mm)

PF 1.5

0.47 (12 mm) dia.

5.51 (140.0 mm)

4.57 (116.0 mm)

3.54(90.0mm)

4.57(116.0mm)

4.57 (116.0 mm)

3.54 (90.0 mm)

4.57(116.0mm)

5.51(140.0mm)

0.43 (11 mm) dia.

9.45 (240.0 mm)

Indoor Pendant Ceiling Mount

Indoor Pendant Wall Mount

Table 2-9 ACUIX ES Pendant Ceiling and Wall Mount Specifications

Ceiling Mount Wall Mount

Dimensions 14.76" (375 mm) (H) x 5.51" (140mm) (W) x 4.57" (116 mm) (L)

5.51" (140 mm) (H) x 4.57" (116mm) (W) x 9.45" (240 mm) (L)

Pipe specification 1.5" NPT 1.5" PT TAP

Weight 4 lbs (1.8 kg) 8.6 lbs (3.9 kg)

Maximum Load Up to 25 lbs (11.7 kg) Up to 22 lbs (10 kg)

Material Aluminum Aluminum


42/86

42


How to Install a Pendant or Surface Dome

1. Select a location to install the components and applicable mount and run the fieldwiring through the skirt or top cap:

Indoor Pendant (ceiling or wall mount)a. Drill the mount hole size into the ceiling or wall. For ceiling and wall mount hole

dimensions see Figure 2-6.

b. Before securing the mount to the wall or ceiling, pull the field wiring through themount, ensuring that it extends at least 12 inches (305 mm) past the end of thepipe.

c. Pull the field wiring from the mount through the top cap (Figure 2-5) and cut thecable length to 6 inches (152 mm).

d. Screw the housing top cap into the wall or ceiling pipe.

Surface (using the skirt)

a. Pull the wires through the skirt wiring access hole and mount the skirt on the

ceiling using the appropriate hardware.b. Finish pulling the field wiring through the skirt. Cut the cable length to 6 inches

(152 mm).

2. For all installations, complete Setting the Switches on page 28.

3. Finish connecting the wiring to the scan assembly:

a. Attach the lanyard from the top cap or skirt to the scan assembly.

b. Remove the terminal plugs from the back of the scan assembly (Figure 2-3).

c. Screw the wires into the plugs.

d. Plug the connectors back into the scan asssembly.

e. Optional Connect BNC (for coax) (see Figure 2-3).

f. Secure the scan assembly to the top cap or skirt using the three provided 8-320.375 Pan Phil machine screws.

4. For both installations, align the three hooks on the cover with the three holes on theinside of the top cap or skirt. Rotate the cover until it is secure inside the top cap orskirt. See Figure 2-7for an example.

5. For both installations, align the two holes on the lower dome with the two screw holeson either side of the scan assembly. Use the two screws provided to secure the lowerdome to the scan assembly.

Figure 2-7 Insert Cover into Skirt or Top Cap and Turn to Secure

Skirt base or top cap - insert coverhooks into each hole and turn cover

Cover- insert and turn hooks into

the skirt base or top cap to secure


43/86


Document 800-01949 Rev D 4305/09

Installing In-Ceiling Domes

Note Each dome requires a 24V AC at 1 A or 12V DC at 1.5A 15% power sourcewhen measured at the dome. To maintain 24V AC at 1 A or 12V DC at 1.5A 15% at each dome, the proper wire size for the distance and the number ofdomes must be determined.

The following explains how to install into a dropped (false) ceiling or a hard ceiling. Fordropped ceiling installations, use a separately ordered ceiling plate (Honeywell partnumber 517082-7130). In addition to the other items normally supplied by the installer, thefollowing may be required:

Tape or plastic channel to prevent dust and material from dropping from the ceiling.

Safety cable - a 3/32 (approximately 2.4 mm) plastic coated aircraft cable with alooping sleeve is recommended.

Figure 2-8 In-ceiling Dome Layout

How to Install an In-ceiling Dome for a Dropped or Hard Ceiling

1. Select a location to install the in-ceiling dome(s).

2. Prepare the ceiling and/or ceiling tile:

Hard Ceiling

Using the mounting template, cut a 7 5/8 (194 mm) diameter hole in the ceiling.If the ceiling is drywall or plaster, it is recommended to seal the entire perimeter ofthe hole with tape or plastic channel to prevent dust and material fromcontaminating the camera.

Dropped (False) Ceiling

a. Remove the ceiling panel at the dome location.

b. Place the ceiling tile on the dropped ceiling plate (Honeywell part number517082-7130).

c. Trim the ceiling tile and press it into the dropped ceiling plate.

Cable can

Lower dome

Turning screws

and wing tabs

Trim ring

Cable can wiring access

hole and clamp

Scan assembly

and housing


44/86

44


d. Using the mounting template, cut a 7 5/8 (194 mm) diameter hole in the ceilingtile flush with the hole in the center of the plate.

3. If required, secure a safety cable to a building supportstructure. Attach the safety cable (from the buildingsupport structure) to the outside of the housing by:

a. Threading the safety cable through a loopingsleeve,

b. Attach to the safety cable bracket on thehousing,

c. Back through the looping sleeve, and then

d. Crimp the looping sleeve to secure the safetycable.

4. Unsnap/remove the cable can and complete Setting the Switches on page 28.

5. Finish connecting the wiring to the outside of the scan assembly housing (Figure 2-9):

a. Remove the plugs and screw the applicable wires into the plug holes.

b. Press the plugs back into the holes.c. Optional Connect BNC (for coax).

6. Pull all the wiring from the plugs through the cable can wiring hole. Ensure the wiringextends at least 12 inches (305 mm) past the end of the hole and cut the cable lengthto 6 inches (152 mm).

7. Tighten the wire clamp to hold the wires in place (see Figure 2-8).

8. Snap the cable can back into place by inserting the two tabs on the cable can into thetwo holes on the scan assembly housing to secure it. See Figure 2-9.

Figure 2-9 In Ceiling Scan Assembly with Switch, Plugs and BNC Connector

9. Insert the cable can and housing through the hole in the ceiling.

a. Turn the wing tab turning screws to make sure the space between the wing tabson the housing and the housing flange is greater than the thickness of the ceiling.See Figure 2-8.

To increase the space, turn the screw clockwise.

To decrease the space, turn the screw counterclockwise.

Housing safety cable

bracket

Cable can with tabs

SW1 and Plugs 1, 2 and 3

BNC connector


45/86


Document 800-01949 Rev D 4505/09

b. Make sure the wing tabs on the housing are staggered so the tabs are not at thesame height See Figure 2-10.

c. Position the wing tabs flat against the housing.

d. Using a Phillips screwdriver, turn the three screws in the housing clockwise torotate the tabs out and tighten the tabs against the ceiling.

The recommended maximum torque is 11.25 N-m (Newton meters) or0.740.92 lbf-ft (pound-force-foot) or 8.85 11.06 lbf-in (pound-force-inch).

Figure 2-10 Stagger the Wing Tabs

10. Insert the trim ring into the inside of the scan assembly housing and rotate it until thethree hooks on the trim ring are aligned and secure underneath the three round tabs.See Figure 2-11.

11. Install the lower dome.

a. Attach the lanyard from the lower dome to the inside of the housing.

b. Align the two holes on the lower dome with the two holes on either side of thescan assembly.

c. Use the screws provided to secure the lower dome to the scan assembly.

Figure 2-11 Inside the In-ceiling Scan Assembly and Housing

Clip lanyard to this bracket

Secure trim ring to the 3 hooks

Turn three screws clockwise to tightenthe tabs to the ceiling (seestep 9d)


46/86

46



47/86


05/09

3

Configuring the ACUIX ES

In this section:

Before You Begin Configuring on page47.

Configuring Display, Control, and Camera Menu Functions on page 53.

Configuring Default Functions: Presets and Tours on page 59.

Configuring Mimic Tours on page 60.

Configuring Presets and Preset Tours on page 61.

Configuring Privacy Zones on page 63.

Configuring Sectors on page 66.

Configuring Contacts/Alarms (Optional) on page 67.

Before You Begin Configuring

See Important Information About Protocols on page 18.

Step 1: Prepare the Controller and Monitor for Use

Before making configuration changes with any controller, you need to:

1. Ensure the dome is assigned to the controller being used. Refer to the applicablecontroller user guide for instructions.

2. Confirm video is displaying on the monitor.

3. Confirm there is manual control of the dome using the controller. To manuallycontrol an ACUIX ES and pan, tilt, zoom, focus, and iris, the address must beselected as the control dome. If the dome ID is turned on (see Displaying the Dome(Camera Msg) Number on the Monitor on page 53), then the letter M is displayed onthe monitor.


48/86

48


Step 2: Turn On (Power Up) the Dome and Find the Mechanical Home

The dome locates other referenced positions (such as presets) using a mechnical home (orindex) position as a reference point. The dome also needs to locate the mechanical

home/index position before responding to the first pan, tilt, and zoom command. For allprotocols the operator can send any command to the dome, but what happens when thedome is first turned on depends on options as listed in Table 3-1.

To find home (MAXPRO-mode or Diamond protocols)

On the controller, press and hold the Fn key, then press F1.

Note For other protocols (VCL, VCL UTC, Pelco P, Pelco D and IntelliBus) there isno command to find home during regular operation.

Step 3: Learn How to Use the Special Presets

There are several special presets reserved for controlling and programming the ACUIX ES.See Programming Preset Tours on page 61to program new presets.

A maximum of 100 presets (including special presets) are supported. Various presets areavailable for programming with all protocols with exceptions as noted in Table 3-2.

Table 3-1 Display Options at Dome Power Up

When the dome firstpowers up

If Then See

Start up screen text The startup screen msg isON

the protocol, baud rate, parity,data bits, camera model, andfirmware release dates andversions display on themonitor.

Changing the Startup

Screen Msg on page53

The startup screen msg isOFF

anXdisplays on the monitor.

Finding home The dome is set to find homeon startup

the message FindingHome...displays on themonitor followed by HomeFound...

Finding the

Mechanical Home on

Startup on page 55

If the dome is not set to findhome on startup

it finds home when the firstcontrol command is receivedat which time the operator cancontrol the dome with thecontroller.


49/86


Document 800-01949 Rev D 4905/09

Note For Pelco P_AD and Pelco D_AD switch settings and special presets, seeAppendix A.

Table 3-2 Special Presets Based on Protocol

Preset Function Protocol Cross Reference

72 Recover encrypted user login PIN and GUID All page 75

73 Enable broadcast command receive mode MAXPRO-mode, VCL,VCL UTC, Diamond andPelco D and P

page 76

74 Disable broadcast command receive mode MAXPRO-mode, VCL,VCL UTC, Diamond andPelco D and P

page 76

75 Administrator / password/PIN settings 1. User Login PIN

2. Change PIN

5. System Info

6. Change Address, Protocol

All System Administrationand Settings, page 71

80, 81,82

Run mimic tours 1, 2 and 3 MAXPRO-mode, VCL,VCL UTC, Pelco D and P

page 60

83, 84,85

Program mimic tours 1, 2 and 3 MAXPRO-mode, VCL,VCL UTC, Pelco D and P

page 60

86 Stop or end mimic tour programmingsequence

MAXPRO-mode, VCL,VCL UTC, Pelco D and P

page 60

87, 88,89

Start/run preset tours 1, 2 and 3 MAXPRO-mode, VCL,VCL UTC, Pelco D and P

page 61

90 Setup menu (on-screen display/OSD) MAXPRO-mode, VCL,VCL UTC, Diamond andPelco D and P

Step 4: Open the OSD

Menu and Start

Configuring, page 50

91, 97and 99

94 and95

Reserved

Reserved and not available with the SonyFCB EX-45C camera

MAXPRO-mode, VCL,VCL UTC, Diamond,Pelco D and P

n/a

92 Toggles auto exposure or iris ON and OFF(factory default is ON)

MAXPRO-mode, VCL,VCL UTC, Diamond and

Pelco D and P

page 57

93 Toggles backlight compensation ON andOFF (preset 92 /auto exposure must be ON)

MAXPRO-mode, VCL,VCL UTC, Diamond andPelco D and P

page 57

96 Run the Flashback function MAXPRO-mode, VCL,VCL UTC, Pelco D and P

page 50

98 Camera lens reset or cycles the power(camera dependent)

All page 72


50/86

50


Accessing Special Presets

Press [preset number] >Presetbutton on the controller.

Using the Flashback Preset

Press 96 >Preset to toggle between two saved positions and quickly return to ascene of interest.

Step 4: Open the OSD Menu and Start Configuring

Note The availability of OSD menus is based on the protocol (MAXPRO-mode,VCL, VCL UTC, Diamond, Pelco P or Pelco D) and the camera model. SeeImportant Information About Protocols on page 18.

Note If the PIN feature is enabled (see Working with Passwords and PINS on page75), the Loginscreen displays and a PIN is required to access the OSD.

1. Enter a PIN or skip to step 2.

a. If prompted, enter the 4-digit PIN to log in as User Level 1 (the default is 1000).Move the joystick up or down to select numbers for each digit. Move the joystickleft or right to move between digits.

b. Press F5 (enter).

2. Press 90> Preset.The main OSD menu, including the camera model, displays after entering the setupmenus.

3. Open the submenus or select a menu:

Press a number beside the menu option. The numbers either toggle between theavailable choices or opens another menu.

Move the joystick up or down the menu and press F5 (enter).

4. Configure the dome as required using Figure 3-1and the following instructions.


51/86


Document 800-01949 Rev D 5105/09

Exiting or Escaping from a Menu

Note Depending on the protocol used, for example with the HJZTP controller, the

monitor displays different exit instructions.

To exit or escape from a menu (VCL):

The monitor displays press Iris Close. Press Iris (-).

Note In VCL protocol, press Iris (+)to open a menu and Iris(-) to close a menu. The OSD uses the terms Iris OpenandIris Closeto mean the same thing respectively. Insome menus, you can also use these keys to toggle

between values.

To exit or escape from a menu (MAXPRO-mode or Diamond):

The monitor displays press Esc. When using an HJZTP controller, press lock.

Iris open

Iris close


52/86

52


Figure 3-1 On-Screen Menu Layout Sony FCB-EX45C Color Camera

1.Language

2.DisplayOptions

3.ControlOptions

4.DiagnosticOptions

5.CameraOp

tions(FCBEX-45C)

6.FunctionProgramming

English(default)

1.Ca

meraMsg

1.PASS

1.Coordinates

1.Zoom

1.n/a

Spanish(Espanol)

(1)MaxDigitalZoomMag

Polish(Polski)

(2)ManualZ

oomSpeed0-8

German(Deutsch)

Italian(Italiano)

French(Francais)

2.Se

ctors

2.Auto-Pivot

2.ShowRunTimeCounter

2.ExposureC

ontrol

2.Program

aPresetTour

Dutch(Nederlands)

(2)ExposureLevel

(8)Backlig

htCompensation

3.PresetName

3.ProgramAlarms

3.CleartheMemory

3.NightshotControl

3.PrivacyZoneOptions

(1)ProgramAlarms

notavailable

withFCBEX-45C

(1)ChangePrivZonePriority

(2)SetAlarmCondition

butmaydisp

layonscreen

(2)Enable/disablePrivacyZo

ne

(3)PrivacyZoneColor

(4)DeletePrivacyZones

4.DigitalZoom

Mag

4.SetPanandTiltOptions

4.n/a

4.WhiteBala

nce

4.ListPS/PT/Sectors

(1)ManualSpeed(deg

/s)

(1)HighLightWBMode

(1)Presets

(2)PanReverse

(2)LowLigh

tWBMode

(2)PresetTours

(3)TiltReverse

(3)EnterHig

hLght28dB

(3)Sectors

(4)-2degTiltLimit

(4)EnterLowLght28dB

(5)FindHomeonStartup

(5)ManualW

hiteBalance

(6)PanOffset

Offset

SetPanOffset

(7)StartupStateResto

re

5.StartupScreenMsg

5.SetDefaultFunction

5.n/a

5.n/a

5.Program

Sector

6.Ch

angeCameraNameLoc

6.AutoFocus

6.RestoreDefaultSettings

6.VerticalPh

aseEdge

6.ProgramPrivacyZone

7.Ch

angeSectorNameLoc

7.PresetTourAutoFocus

7.ScanandDomeReset

7.VerticalPh

ase0-359

7.DeletePS/PT/MT/Sectors

8.Crosshairs

Preset75:AdminLoginand

PasswordSettings

1.UserLoginPIN

2.ChangePin

4.PrivZoneSecurityLevel

9.Do

meNameSettings

5.System

Info

(1)

SetDomeName

6ChangeAddress/Protoco

l

(2)

DisplayDomeName

(3)

ChangeDomeName

Loc

ation

ACUIXESOn-

ScreenDisplay(OSD)Menus


53/86


Document 800-01949 Rev D 5305/09

Configuring Display, Control, and Camera Menu Functions

Note Remember, open the OSD by pressing 90> Preset.After each step it isassumed that you exit and saveafter each task using the applicable methodbased on the protocol and controller.

Configuring the Monitor and Text Display Settings

Task/Action with Default Notes

Changing the On-screen Language

Scroll to select 1 Language > English (default),French (Francais), German (Deutsch), Italian(Italiano), Spanish (Espanol), Dutch(Nederlands), Polish (Polski).

Displaying the Dome (Camera Msg) Number on the Monitor

Select 2 Display Options > 1 Camera Msg>ONor OFF (default).

See Note 1.

Changing the Digital Zoom Magnification Level (Digital Zoom Mag) Select 2 Display Options > 4 Digital Zoom Mag

> ONor OFF(default).Displays the magnifcation level on the right side besidethe dome ID. If the location changes based on domename, this text also moves.

Changing the Startup Screen Msg

Select 2 Display Options > 5 Start up ScreenMsg > ON(default) or OFF.

Changing Dome (Camera) Name/Msg Loc (Location)

Select 2 Display Options > 6 Change CameraName Loc > Depending on the protocol, use

either arrows or the joystick to move the text up ordown the monitor to position as required.

See Note 1.

Displaying Crosshairs on the Monitor

Select 2 Display Options > 8Crosshairs > ONor OFF (default).

Useful with pan offset.


54/86

54


Configuring the Controller Settings - Pan and Tilt Reverse

Setting a Dome Name

Select 2 Display Options > 9 Dome Name

Settings > 1 Set Dome Name> enter a24-alphanumeric name for the dome. Dependingon the protocol, use either arrows or the joystickto scroll the number and letter choices.

See Note 2.

Displaying a Dome Name

Select 2 Display Options > 9 Dome NameSettings > 2 Display Dome Name> ONor OFF(default).

See Note 2.

Changing Dome Name Location

Select 2 Display Options > 9 Dome NameSettings > 3 Change Dome NameLocation >

Depending on the protocol, use either arrows orthe joystick to move the text up or down themonitor to position as required.

See Note 2.

Display Options Notes:

(1) Applies to the numerical number assigned to each dome (displays on the monitor as CAM) during installationusing the address switches on the scan assembly. To name and position the text on the monitor see ChangingDome Name Location on page 54.

(2) Applies to the user-assigned alpha-numeric name you can assign to each dome. The dome may also have anumber assigned during installation when the address switch settings are assigned.



Turning the Pan Reverse ON or OFF

Select 3 Control Options > 4 Set Pan and TiltOptions> 2 Pan Reverse > ON orOFF(default).

If set to ON, a left pan command causes the dome topan right. A right pan command causes the dome topan left.

Turning the Tilt Reverse ON or OFF

Select 3 Control Options > 4 Set Pan and TiltOptions> 3 Tilt Reverse > ON orOFF(default).

If set to ON, a tilt up command causes the dome to tiltdown. A tilt down command causes the dome to tilt up.


55/86


Document 800-01949 Rev D 5505/09

Configuring the Pan, Tilt and Zoom (PTZ) and Dome Control Settings


Turning the Pan and Tilt Speed Range (PASS) ON and OFF

Select 3 Control Options > 1 PASS >ON(default) or OFF.

PASS is a function of the lens zoom angle. Themaximum pan and tilt speeds are reduced when thelens zooms in. For example, the pan and tilt functionsare slow when the dome is set at 12X zoom. The higherthe zoom magnification, the slower the speed.

Turning the Auto Pivot ON or OFF

1. Select 3 Control Options > 2 Auto Pivot> ON(default) or OFF.

Track people passing directly underneath the dome.The dome automatically turns 180 when it reaches itslower limit. It continues to tilt up as long as the controller

tilt function remains in the down position. When thedome reaches its tilt up limit, it returns to normaloperation.

Changing the Degree of the Manual Pan and Tilt Speed

Select 3 Control Options > 4 Set Pan and TiltOptions> 1 Manual Speed deg/s > 90 /sec or180 /sec or 360 /sec (default).

The maximum tilt speed is half of the maximum panspeed.

Turning the -2 Tilt Limit ON or OFF

Select 3 Control Options > 4 Set Pan and TiltOptions> 42 Tilt Limit > ONor OFF(default).

ON positions the dome tilt to 2 above horizontal.

Finding the Mechanical Home on Startup

1. Select 3 Control Options > 4 Set Pan and TiltOptions> 5 Find Home on Startup >

2. Select ONor OFF(default).If you select ON, the message ExtremeCaution: This will cause the scan tomove immediately on startup...displays.

SelectY(yes) to continue or N (no) to cancel.

ON sets the dome to find the mechanical home (orindex) position after an initial startup delay of 15seconds.

OFF sets the unit to find home when powered upand the dome performs a control command.

When a privacy zone is enabled, no video isshown during the finding home process andprivacy zones are not recognized until the domereaches home. Once the dome finds home, apicture can be viewed on the monitor unless aprivacy zone overlaps with this home setting. See

Configuring Privacy Zones on page 63.

Turning the Pan Offset ON or OFF

Select 3 Control Options > 4 Set Pan and TiltOptions> 6 Pan Offset> 1 Pan Offset> ONorOFF(default).

Pelco P and D protocols only: The pan offset feature isnot available due to the pre

ACUIX ES 800-01949 Full Guide Camara Domo

Documents

Transcript of ACUIX ES 800-01949 Full Guide Camara Domo